INSTALLATION
Removal / installation · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| 1.
INSTALL GENERATOR ASSEMBLY |
 |
- Install the generator assembly with the bolt.
-
Torque:
- 62 N*m{
632 kgf*cm
, 46 ft.*lbf
}
Install the generator wire to terminal B with the nut.
-
Torque:
- 9.8 N*m{
100 kgf*cm
, 87 in.*lbf
}
Install the terminal cap.
Connect the generator connector.
| 2.
INSTALL GENERATOR BRACKET |
 |
- Install the generator bracket with the 2 bolts.
-
Torque:
- 36 N*m{
367 kgf*cm
, 27 ft.*lbf
}
| 3.
INSTALL IDLE NO.2 PULLEY ASSEMBLY (w/ Air Conditioning System) |
 |
- Install the idle No.2 pulley assembly and washer with the bolt.
-
Torque:
- 45 N*m{
459 kgf*cm
, 33 ft.*lbf
}
| 4.
INSTALL AIR CLEANER HOSE ASSEMBLY
|
 |
Install the air cleaner hose assembly with the clamp.
| 5.
INSTALL AIR TUBE ASSEMBLY
|
 |
Install the air tube assembly with the 2 clamps and 2 bolts.
| 6.
INSTALL VENTILATION PIPE
|
 |
- Install the ventilation pipe with the bolt and clip.
-
Torque:
- 20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
| 7.
INSTALL COMPRESSOR OUTLET ELBOW |
 |
- Install the compressor outlet elbow with the 2 bolts and 2 clamps.
-
Torque:
- Bolt (A):
- 12 N*m{
122 kgf*cm
, 9 ft.*lbf
}
- Bolt (B):
- 32 N*m{
326 kgf*cm
, 24 ft.*lbf
}
| 8.
INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
|
 |
Provisionally tighten the compressor and magnetic clutch with the 4 bolts.
Tighten the compressor and magnetic clutch with the 4 bolts.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
- NOTICE:
- Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.
| 9.
INSTALL FAN & GENERATOR V BELT
|
 |
Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
- NOTICE:
- Make sure that the fan and generator V belt is set properly on each pulley.
Check that the indicator mark of the V-ribbed belt tensioner (Click here).
| 10.
INSTALL FENDER APRON MUDGUARD SEAL RH |
|
| 11.
INSTALL ENGINE SERVICE HOLE SUB COVER ASSEMBLY
|
 |
Install the engine service hole sub cover with the 5 bolts.
-
Torque:
- 13 N*m{
133 kgf*cm
, 10 ft.*lbf
}
| 12.
INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
 |
- HINT:
- Perform the same procedure as above on the opposite side. (Click here)
| 13.
INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
 |
- HINT:
- Perform the same procedure as above on the opposite side. (Click here)
| 14.
INSTALL FRONT DOOR SCUFF PLATE RH |
|
| 15.
CONNECT NEGATIVE BATTERY CABLE |
|
| 16.
INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1) |
 |
-
Torque:
- 13 N*m{
133 kgf*cm
, 10 ft.*lbf
}
| 17.
PERFORM INITIALIZATION |
 |
Some system need initialization when reconnecting the battery cable. (Click here)