2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT
(Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

4. REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)
  1. Remove the engine under cover No.2 together with the engine side under cover LH and engine side under cover RH (for Wide Body).


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the engine coolant in a container and dispose of it according to local regulations.

  1. Loosen the radiator drain cock plug and drain the engine coolant.

    A316495E01

    Text in Illustration 
    *1
    Radiator Reservoir Cap Sub-assembly
    *2
    Radiator Reservoir Assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Water Drain Cock Plug
    *5
    2-Way
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in a disposable oil container.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


7. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side. (Click here)


8. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side. (Click here)


9. REMOVE FRONT DOOR SCUFF PLATE RH

10. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.


11. REMOVE CAM POSITION SENSOR

  1. A086888
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


12. REMOVE FAN & GENERATOR V BELT

  1. A102135E01
    Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.

    NOTICE:
    When removing the drive belt, do not use the idle pulley's bolt.

    HINT:
    After removing the drive belt, move the tensioner upward to the maximum amount.


13. DISCONNECT RADIATOR HOSE INLET
  1. Remove the clamp, and disconnect the radiator hose inlet from the engine.


14. DISCONNECT RADIATOR HOSE OUTLET
  1. Remove the clamp, and disconnect the radiator hose outlet from the engine.


15. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

  1. A103325
    Disconnect the fuel vapor feed hose from the VSV.


16. DISCONNECT UNION TO CONNECTOR TUBE HOSE
  1. Disconnect the union to connector tube hose from the intake manifold.


17. REMOVE INTAKE AIR CONNECTOR

  1. A102437E01
    Slide the clamp and disconnect the No. 2 ventilation hose and vacuum hose. (A)

  1. Loosen the 2 hose clamp bolts. (B)

  1. Remove the 2 bolts and intake air connector. (C)


18. DISCONNECT FUEL HOSE

  1. A087751E01
    Pull the fuel hose connector cover up to release the lock. (Click here)

  1. Disengage the fuel connector to disconnect the fuel hose. (Click here)


19. DISCONNECT FUEL HOSE NO.2
  1. Remove the clamp, and disconnect the fuel hose No.2 from the delivery pipe.


20. DISCONNECT VANE PUMP ASSEMBLY

  1. A102130E01
    Disconnect the PS fluid pressure switch connector.

  1. Remove the 2 bolts and disconnect the pump from the engine.

  1. Support the vane pump securely.


21. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY

22. REMOVE OIL LEVEL GAUGE GUIDE

  1. A102132E01
    Remove the bolt and gauge guide.


23. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
  1. Disconnect the compressor connector.

  1. A102804E02
    Remove the 4 bolts and disconnect the compressor from the engine.

    HINT:
    Disconnect the compressor with the low pressure hose and high pressure hose stuck by suspended from the rope.

  1. Support the cooler compressor securely.


24. DISCONNECT ENGINE WIRE
  1. Disconnect the wire harness support of the ECM.

  1. Disconnect the connectors of the ECM.

  1. Disconnect the clamps of the engine wire and earth cable.

  1. Disconnect the +B terminal of the starter and connector from the generator.

  1. A101143E03
    Remove the nut and disconnect the cable from the engine room J/B.


25. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

  1. A102438E01
    Disconnect the throttle motor connector. (A)

  1. Slide the clamp and disconnect the water by-pass hose. (B)

  1. Slide the clamp and disconnect the No. 2 water by-pass hose. (C)

  1. for Type A:
    Remove the 2 bolts and 2 nuts, and then remove the throttle body assembly. (D)

  1. for Type B:
    Remove the 4 bolts and throttle body assembly. (D)

  1. G037700
    Remove the gasket from the intake manifold.


26. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the injectors when removing the delivery pipe.

  1. A087156
    Disconnect the fuel hoses.

  1. Disconnect the 4 injector connectors.

  1. Remove the 2 bolts O-ring and fuel pulsation damper assembly.

  1. Remove the 2 bolts and delivery pipe together with the 4 injectors.

  1. Remove the delivery pipe spacers.

  1. A087158
    Using a screwdriver, pry out the 4 spacers from the cylinder head.


27. REMOVE INJECTOR ASSEMBLY

  1. A087157E01
    Pull out the 4 injectors from the delivery pipe.

  1. Remove the O-rings from the injectors.


28. REMOVE INTAKE MANIFOLD
  1. Disconnect the ventilation hose No.3.

  1. A102806E01
    Remove the 5 bolts, 2 nuts, intake manifold and gasket.


29. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan pulley and fan spacer.


30. REMOVE WATER BY-PASS PIPE NO.1
  1. Remove the bolt, 2 nuts, water by-pass pipe and gasket.


31. REMOVE WATER INLET

  1. A087301
    Remove the 2 nuts, bolt, water inlet and gasket.


32. REMOVE THERMOSTAT

  1. A086841J01
    Remove the thermostat.


33. REMOVE GENERATOR ASSEMBLY

  1. A088507
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the 3 bolts and generator assembly.


34. REMOVE COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning)

  1. A337819
    Remove the 5 bolts and compressor mounting bracket No.1.


35. REMOVE IDLER PULLEY SUB-ASSEMBLY NO.1

  1. A102170
    Remove the bolt, pulley plate, collar, and idler pulley sub-assembly No.1.


36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A232341
    Remove the 2 bolts and belt tensioner.


37. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the bolts and ignition coil assembly.


38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.


39. REMOVE CRANKSHAFT POSITION SENSOR

  1. G037914
    Remove the bolt and crank position sensor.


40. REMOVE CRANKSHAFT PULLEY

  1. G037261E04
    Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the bearing cap No.1, as shown in the illustration.

  1. A101288E01
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A101289E01
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


41. REMOVE OIL PAN SUB-ASSEMBLY NO.2
  1. Remove the drain plug and gasket.

  1. A101291
    Remove the 18 bolts and 2 nuts.

  1. A101293
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan sub-assembly No.2.

    NOTICE:
    Do not damage the contact surfaces of the oil pans.


42. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A101294E03
    Remove the bolt, 2 nuts, oil strainer and gasket.


43. REMOVE OIL PAN SUB-ASSEMBLY

  1. A264837E01
    Remove the 16 bolts and 2 nuts.

  1. A101296E01
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Do not damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A101297E01
    Remove the O-ring.


44. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A101298E01
    Remove the 19 bolts and 2 nuts shown in the illustration (w/o air conditioning).

  1. A192884
    Remove the 17 bolts and 2 nuts shown in the illustration (w/ air conditioning).

  1. A101299E01
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A101300E01
    Remove the 3 O-rings.

  1. A101979
    Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.


45. REMOVE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, water pump and gasket.


46. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

  1. A101302E01
    Using a screwdriver with its tip taped, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


47. REMOVE OIL PUMP RELIEF VALVE

  1. A086864
    Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the valve spring and relief valve.

← COMPONENTS (from Jan 2015)REMOVAL (from Jan 2015) →