2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT
(Click here)

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

4. REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)
  1. Remove the engine under cover No.2 together with the engine side under cover LH and engine side under cover RH (for Wide Body).


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the engine coolant in a container and dispose of it according to local regulations.

  1. Loosen the radiator drain cock plug and drain the engine coolant.

    A340635E01

    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    *1
    Radiator Reservoir Cap Sub-assembly
    *2
    Radiator Reservoir Assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Water Drain Cock Plug
    *5
    2-Way
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the engine oil from the oil pan sub-assembly.

    NOTICE:
    Collect the oil in a disposable oil container.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }


7. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side. (Click here)


8. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side. (Click here)


9. REMOVE FRONT DOOR SCUFF PLATE RH

10. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.


11. REMOVE CAMSHAFT POSITION SENSOR

  1. A086888
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


12. REMOVE FAN AND GENERATOR V BELT

  1. A102135E01
    Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and decrease the tension in the drive belt. Then remove the drive belt.

    NOTICE:
    When removing the drive belt, do not use the idle pulley's bolt.

    HINT:
    After removing the drive belt, move the tensioner upward to the maximum amount.


13. DISCONNECT RADIATOR HOSE INLET
  1. Remove the clamp, and disconnect the radiator hose inlet from the engine.


14. DISCONNECT RADIATOR HOSE OUTLET
  1. Remove the clamp, and disconnect the radiator hose outlet from the engine.


15. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

  1. A103325
    Disconnect the fuel vapor feed hose from the VSV.


16. DISCONNECT UNION TO CONNECTOR TUBE HOSE
  1. Disconnect the union to connector tube hose from the intake manifold.


17. REMOVE INTAKE AIR CONNECTOR

  1. A102437
    Slide the clamp and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.

  1. Disconnect the vacuum hose from the intake air connector.

  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts and intake air connector.


18. DISCONNECT FUEL HOSE

  1. A309365
    Disconnect the No. 1 fuel hose from the fuel pressure pulsation damper assembly (Click here).


19. DISCONNECT FUEL HOSE NO.2
  1. Remove the clamp, and disconnect the fuel hose No.2 from the delivery pipe.


20. DISCONNECT VANE PUMP ASSEMBLY

  1. A102130E01
    Disconnect the PS fluid pressure switch connector.

  1. Remove the 2 bolts and disconnect the pump from the engine.

  1. Support the vane pump securely.


21. REMOVE OIL LEVEL GAUGE SUB-ASSEMBLY

22. REMOVE OIL LEVEL GAUGE GUIDE

  1. A102132E01
    Remove the bolt and gauge guide.


23. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning)
  1. Disconnect the compressor connector.

  1. A102804E02
    Remove the 4 bolts and disconnect the compressor from the engine.

    HINT:
    Disconnect the compressor with the low pressure hose and high pressure hose stuck by suspended from the rope.

  1. Support the cooler compressor securely.


24. DISCONNECT ENGINE WIRE
  1. Disconnect the wire harness support of the ECM.

  1. Disconnect the connectors of the ECM.

  1. Disconnect the clamps of the engine wire and earth cable.

  1. Disconnect the +B terminal of the starter and connector from the generator.

  1. A101143E03
    Remove the nut and disconnect the cable from the engine room J/B.


25. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

  1. A337883E01
    Disconnect the throttle motor connector.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i

  1. Slide the clamp and disconnect the water by-pass hose from the throttle body assembly.

  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the throttle body assembly.

  1. Remove the 4 bolts and throttle body assembly.

  1. A239457
    Remove the gasket from the intake manifold.


26. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Disconnect the vacuum hose from the fuel pressure regulator assembly.

  1. Slide the clamp and disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.

  1. A341591E01
    Disconnect the 4 fuel injector connectors.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i

  1. Remove the 2 bolts, fuel pulsation damper assembly and O-ring.

  1. Remove the 2 bolts and fuel delivery pipe sub-assembly together with the 4 fuel injector assemblies.

    NOTICE:
    Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.

  1. Remove the 4 injector vibration insulators.

  1. A341592E01
    Using a screwdriver, pry out the 4 injector spacers and 4 O-rings from the cylinder head sub-assembly.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


27. REMOVE INJECTOR ASSEMBLY

  1. A346727E01
    Pull out the 4 fuel injector assemblies from the fuel delivery pipe sub-assembly.
    Text in Illustration 
    *A
    w/ Dual VVT-i
    *B
    w/o Dual VVT-i
    V100135
    Pull Out

  1. Remove the O-rings from the fuel injector assemblies.


28. REMOVE INTAKE MANIFOLD
  1. Disconnect the ventilation hose No.3.

  1. A102806E01
    Remove the 5 bolts, 2 nuts, intake manifold and gasket.


29. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan pulley and fan spacer.


30. REMOVE WATER BY-PASS PIPE NO.1
  1. Remove the bolt, 2 nuts, water by-pass pipe and gasket.


31. REMOVE WATER INLET

  1. A087301
    Remove the 2 nuts, bolt, water inlet and gasket.


32. REMOVE THERMOSTAT

  1. A086841J01
    Remove the thermostat.


33. REMOVE GENERATOR ASSEMBLY

  1. A088507
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the 3 bolts and generator assembly.


34. REMOVE COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning)

  1. A337819
    Remove the 5 bolts and compressor mounting bracket No.1.


35. REMOVE IDLER PULLEY SUB-ASSEMBLY NO.1

  1. A102170
    Remove the bolt, pulley plate, collar, and idler pulley sub-assembly No.1.


36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A232341
    Remove the 2 bolts and belt tensioner.


37. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the bolts and ignition coil assembly.


38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.


39. REMOVE CRANKSHAFT POSITION SENSOR

  1. G037914
    Remove the bolt and crank position sensor.


40. REMOVE CRANKSHAFT PULLEY

  1. G037261E04
    Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the bearing cap No.1, as shown in the illustration.

  1. A101288E01
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A101289E01
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


41. REMOVE OIL PAN SUB-ASSEMBLY NO.2
  1. Remove the oil pan drain plug and gasket.

  1. A101291
    Remove the 18 bolts and 2 nuts.

  1. Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.


42. REMOVE OIL PAN SUB-ASSEMBLY

  1. A336471
    Remove the 16 bolts and 2 nuts.

  1. A336472E03
    Using a screwdriver wrapped in protective tape, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the gasket.


43. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A341680E02
    w/ Air Conditioning:
    Remove the 16 bolts and nut shown in the illustration.
    Text in Illustration 
    *A
    w/o Air Conditioning

  1. w/o Air Conditioning:
    Remove the 18 bolts and nut shown in the illustration.

  1. A101299E04
    Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. A222350E02
    Remove the 3 O-rings.

  1. A101979
    Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.


44. REMOVE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, water pump and gasket.


45. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

  1. A101302E07
    Using a screwdriver with its tip taped, pry out the oil seal.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


46. REMOVE OIL PUMP RELIEF VALVE

  1. A086864
    Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the valve spring and relief valve.

← REMOVAL (Oct 2014 – Dec 2014)INSPECTION (from Oct 2014) →