2014-2019 Hiace · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. BEARING POSITION

D029783E01

Standard:
Mark
Front Race Diameter Inside / Outside mm (in.)
Thrust Bearing Diameter Inside / Outside mm (in.)
Rear Race Diameter Inside / Outside mm (in.)
A
28.45 (1.120) / 47.3 (1.862)
29.2 (1.15) / 50.2 (1.976)
-
B
28.6 (1.126) / 46.4 (1.827)
28.9 (1.138) / 50.2 (1.976)
-
C
24.7 (0.972) / 41.8 (1.646)
24.2 (0.953) / 47.8 (1.882)
-
D
37.2 (1.465) / 58.8 (2.315)
33.8 (1.331) / 50.0 (1.969)
-
E
36.8 (1.449) / 50.9 (2.004)
33.7 (1.327) / 47.6 (1.874)
-
F
-
26.0 (1.024) / 42.8 (1.685)
26.8 (1.055) / 53.67 (2.113)
G
-
49.9 (1.965) / 64.4 (2.535)
53.4 (2.102) / 63.6 (2.504)
H
33.7 (1.327) / 47.6 (1.874)
35.5 (1.398) / 47.7 (1.878)
-
I
28.5 (1.122) / 44.2 (1.740)
27.7 (1.091) / 44.2 (1.740)
-
J
-
39.38 (1.550) / 58.1 (2.287)
-


2. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT05393
    Install the transmission case in the overhaul attachment.


3. INSTALL 1ST AND REVERSE BRAKE PISTON NO.1

  1. AT08209E06
    Coat 3 new O-rings with ATF.

  1. Install the 2 O-rings on the 1st and reverse brake piston No.1.

  1. Install the O-rings on the reaction sleeve.

  1. Install the 1st and reverse brake piston No.1 to the reaction sleeve.


4. INSTALL BRAKE REACTION SLEEVE

  1. D001243
    Coat a new O-ring with ATF, and install it to the reaction sleeve.

  1. With the brake piston No.1 underneath (the rear side), install the brake reaction sleeve and the brake piston No.1 to the transmission case.

    NOTICE:
    Be careful not to damage the O-rings.


5. INSTALL 1ST & REVERSE BRAKE PISTON NO.2

  1. AT08333E05
    Coat new O-ring with ATF.

  1. Install the O-ring on brake piston No.2.

  1. With the spring seat of the piston upwards (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.


6. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. AT05429
    Place the piston return spring onto the 1st and reverse brake piston.

  1. AT08303E02
    Set SST as shown, and compress the return spring with SST.
    SST
    09350-30020   (09350-07050, 09350-07070)

    NOTICE:
    Stop compressing when the spring sheet is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from being deformed.

  1. Using a screwdriver, install the snap ring. Make sure the end gap of the snap ring is not aligned with the spring retainer claw.


7. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

  1. AT05890
    Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.


8. INSTALL REAR PLANETARY FLANGE THRUST NEEDLE ROLLER BEARING

  1. Z005138E02
    Coat the assembled bearing and race with petroleum jelly.

  1. Install it onto the case.

    Bearing diameter:

    Inside
    Outside
    Bearing
    39.38 mm (1.550 in.)
    58.1 mm (2.287 in.)


9. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. AT05107
    Install the leaf spring.

  1. AT08208
    Install the flange with the rounded edge facing upward.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P - D - P

  1. AT07893
    Align the teeth on the flange, the discs and the plates.

  1. Q004066
    Face the snap ring upward (front side), and install the 2nd brake drum to the planetary gear.

    NOTICE:
    Face the oil hole in the drum towards the lower side of the transmission case (the side where the valve body is installed).

  1. Q004068E02
    Align the splines of the transmission case with the assembled rear planetary gear and the 1st and reverse brake with the output shaft, indicated by A.

  1. AT05158
    Install the assembled output shaft.

  1. Z005131E02
    Rest the output shaft on wooden blocks.

  1. AT05396E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


10. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

  1. AT08224
    Using a cylinder gauge, measure the inside diameter of the transmission case rear bushing.

    Maximum inside diameter:
    38.19 mm (1.5035 in.)

    If the inside diameter is greater than the maximum, replace the transmission case.


11. INSTALL 2ND BRAKE PISTON SLEEVE

12. INSTALL BRAKE DRUM GASKET

  1. AT04469
    Coat a new gasket with ATF.

  1. Install the brake drum gasket.


13. INSTALL 1 WAY CLUTCH ASSEMBLY

  1. AT05231
    Install the thrust washer onto the 2nd brake.

  1. Z005133E02
    Install the 1 way clutch.


14. INSTALL 2ND BRAKE PACK

  1. AT05398E03
    Install the 1.8 mm (0.071 in.) thick plate with the rounded edge side of the plate facing the disc.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    D - P - D - P - D - P - D - P - D - P

  1. Install the flange with the rounded edge of the flange facing the disc.

  1. AT05476
    Using a screwdriver, install the snap ring.


15. INSPECT PACK CLEARANCE OF SECOND BRAKE

  1. AT05215
    Using a feeler gauge, measure the clearance between the snap ring and the flange.

    Clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is outside the standard, check for an improper installation.


16. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

  1. Q000840
    While turning the planetary sun gear clockwise, install it into the No.1 one-way clutch.

    HINT:
    Confirm the thrust washer is installed correctly.


17. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. D029745E02
    Coat the bearing and race with petroleum jelly and install them onto the front planetary gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    35.5 mm (1.398 in.)
    47.7 mm (1.878 in.)
    Race
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)

  1. D029741
    Install the front planetary gear to the sun gear input drum.

  1. D029740E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07070)

  1. Remove the wooden blocks or equivalent under the output shaft.

  1. D029744
    Coat the race with petroleum jelly, and install it onto the front planetary gear.

    Race diameter:

    Inside
    Outside
    Race
    53.4 mm (2.102 in.)
    63.6 mm (2.504 in.)


18. INSTALL 2ND COST BRAKE BAND ASSEMBLY

  1. Q004030
    Install the 2nd coast brake band to the case.

  1. Q000788
    Install the E-ring to the pin.

  1. Install the pin through the brake band.

  1. Install the E-ring to the pin.


19. INSTALL DIRECT CLUTCH ASSEMBLY

  1. D006214E04
    Install the bearing and the thrust washer to the forward clutch.

  1. AT05262E02
    Install the direct clutch to the forward clutch.


20. INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. Z005137E02
    Coat the bearing and the race with petroleum jelly, and install them onto the forward clutch.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    42.8 mm (1.685 in.)
    Race
    26.0 mm (1.024 in.)
    42.8 mm (1.685 in.)

  1. Z005136E02
    Coat the race with petroleum jelly, and install it onto the front planetary ring gear.

    Race diameter:

    Inside
    Outside
    Race
    26.8 mm (1.055 in.)
    53.67 mm (2.113 in.)

  1. AT05432
    Align the flukes of the discs in the forward clutch.

  1. Q000838E02
    Align the splines of the front planetary ring gear with the flukes of the discs and install the front planetary ring gear to the forward clutch.


21. INSTALL FORWARD CLUTCH ASSEMBLY

  1. AT08306E02
    Coat the bearing and the race with petroleum jelly, and install them onto the ring gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    32.6 mm (1.283 in.)
    47.7 mm (1.878 in.)
    Race
    30.6 mm (1.205 in.)
    53.6 mm (2.110 in.)

  1. AT08234
    Install the assembled direct clutch, the forward clutch and the front planetary ring gear into the transmission case.

  1. AT05213
    Using vernier calipers, measure the distance between the sun gear input drum and the direct clutch drum as shown in the illustration.

    Distance:
    5.3 to 7.3 mm (0.209 to 0.287 in.)

    If the distance is outside the standard, check for an improper installation.

  1. Z005236E02
    Coat the bearing with petroleum jelly and install it onto the forward clutch.

    Bearing:

    Inside
    Outside
    Bearing
    33.7 mm (1.327 in.)
    47.6 mm (1.874 in.)


22. INSTALL 2ND COAST BRAKE PISTON

  1. AT05086
    Coat 2 new O-rings with ATF, and install them to the cover.

  1. Install the spring, the piston assembly and the cover to the case.

  1. AT05127E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


23. INSTALL PISTON STROKE OF 2ND COST BRAKE

24. INSTALL OVERDRIVE SUPPORT SUB-ASSEMBLY

  1. AT05110E03
    Coat the bearing and the race with petroleum jelly, and install it onto the O/D support assembly.

    Bearing and race diameter:

    Inside
    Outside
    Race
    36.8 mm (1.449 in.)
    50.9 mm (2.004 in.)
    Bearing
    33.8 mm (1.331 in.)
    50.0 mm (1.969 in.)

  1. AT05159
    Confirm the thrust washer is installed correctly.

    HINT:
    Make sure that the lug shape fits into the hole on the O/D support assembly.

  1. AT05400E02
    Using 2 bolts of SST, aim the bolt and the oil holes of the O/D support toward the valve body side, and align them with the bolt holes of the transmission case, and insert.
    SST
    09350-30020   (09350-07020)

  1. Temporarily tighten the 2 bolts.

  1. Q000618E02
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)

    HINT:
    Install the snap ring open end toward the valve body.

  1. AT05218
    Torque the 2 bolts.

    Torque:
    25 N*m{ 260 kgf*cm , 19 ft.*lbf }


25. INSPECT OUTPUT SHAFT

  1. Z006796
    Using a dial indicator, measure the end play of the output shaft with hand.

    End play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the values are outside the standard, check for an improper installation.

  1. Check that the output shaft rotates smoothly.


26. INSTALL OVERDRIVE BRAKE PACK

  1. AT05763
    Install the 4.0mm(0.157 in.) thick flange (flat ring) with the rounded edge side of the flange facing the discs.

  1. Install the plates and discs.

    Install in order:
    P = Plate D = Disc
    P - D - P - D - P - D

  1. Install the flange (stepped ring) with the flat side of the flange facing the disc.

  1. AT05233
    Using a screwdriver, install the snap ring.


27. INSPECT OVERDRIVE BRAKE PISTON

  1. AT05282E02
    Place SST and a dial indicator onto the O/D brake piston.
    SST
    09350-30020   (09350-06120)

  1. AT05147
    Measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Piston stroke:
    1.75 to 2.05 mm (0.0689 to 0.0807 in.)

    If the piston stroke is less than the limit, parts may have been assembled incorrectly, so check and reassemble again.
    If the piston stroke is still outside the standard, select another flange.

    HINT:
    There are 7 different thicknesses for the flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)
    -
    -


28. INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY

  1. Q000842
    Coat the race with petroleum jelly, and install it onto the O/D support.

    Race diameter:

    Inside
    Outside
    Race
    37.2 mm (1.465 in.)
    58.8 mm (2.315 in.)

  1. AT05146
    Install the O/D planetary ring gear.

  1. AT05126
    Coat the bearing and race with petroleum jelly, and install them onto the planetary ring gear.

    Bearing and race diameter:

    Inside
    Outside
    Bearing
    26.0 mm (1.024 in.)
    46.8 mm (1.843 in.)
    Race
    24.2 mm (0.953 in.)
    47.8 mm (1.882 in.)

  1. Z005128
    Coat the race with petroleum jelly, and install it onto the planetary gear.

    Race diameter:

    Inside
    Outside
    Race
    24.7 mm (0.972 in.)
    41.8 mm (1.646 in.)

  1. Q000619
    Install the O/D planetary gear, O/D direct clutch and 1 way clutch.

  1. AT04470E02
    Place SST on the transmission case.
    SST
    09350-36010   (09350-06090)

  1. Using vernier calipers, measure the distance between the tops of SST and the clutch drum.

    Standard distance:
    15.5 to 16.5 mm (0.610 to 0.650 in.)

    If the distance is outside the standard, check for an improper installation.

  1. AT08313E02
    Coat the bearing with petroleum jelly and install it onto the O/D direct clutch.

    Bearing diameter:

    Inside
    Outside
    Bearing
    29.2 mm (1.150 in.)
    50.2 mm (1.976 in.)


29. INSTALL OIL PUMP ASSEMBLY

  1. Z005237E02
    Coat the race with petroleum jelly, and install it onto the oil pump.

    Race diameter:

    Inside
    Outside
    Race
    28.45 mm (1.120 in.)
    47.3 mm (1.862 in.)

  1. Coat a new O-ring with ATF, and install it around the pump body.

  1. Place the oil pump through the input shaft, and align the bolt holes of the pump body with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the O/D direct clutch drum.

    NOTICE:
    Do not push on the oil pump strongly, or the oil seal ring will stick to the direct clutch drum.

  1. AT05404
    Install the 7 bolts.

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }


30. INSPECT INPUT SHAFT SUB-ASSEMBLY

  1. AT05244E02
    Make sure the input shaft rotates smoothly.


31. INSPECT INDIVIDUAL PISTON OPERATION INSPECTION

  1. AT05275E06
    Check for the sound while applying compressed air into the oil hole indicated in the illustration.

    HINT:
    Inspect the overdrive direct clutch with the C-0 accumulator piston hole closed. If there is no sounds from the overdrive direct clutch, disassemble and check the installation conditions of the following parts:


    1. Overdrive direct clutch

    2. Direct clutch

    3. Forward clutch

    4. Overdrive brake

    5. 2nd coast brake

    6. 2nd brake

    7. 1st and reverse brake


32. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. AT05238E02
    Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals.
    SST
    09350-30020   (09350-07110)

  1. Coat the oil seal lip with MP grease.


33. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. D031556E03
    Install a new spacer to the manual valve lever.

  1. Install the manual valve lever shaft to the transmission case through the manual valve lever.

  1. AT05405
    Using a hammer, drive in a new pin.

  1. D006523
    Align the manual valve lever indentation with the spacer hole, and stake them with a punch.

  1. Make sure that the shaft rotates smoothly.


34. INSTALL PARKING LOCK PAWL SHAFT

  1. Q000776E02
    Install the E-ring to the shaft.

  1. Install the parking lock pawl, the shaft and the spring.


35. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. Z006797
    Connect the parking lock rod to the manual valve lever.


36. INSTALL PARKING LOCK PAWL BRACKET

  1. AT05406
    Install the parking lock pawl bracket with the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Z005222E02
    Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the pawl.


37. INSTALL C-0 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-ring with ATF, and install them to the piston.

  1. D028075
    Install the 2 springs and accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    C-0 Inner
    46.0 mm (1.811 in.)
    14.02 mm (0.552 in.)
    Yellow
    C-0 Outer
    74.6 mm (2.137 in.)
    20.9 mm (0.823 in.)
    Orange


38. INSTALL B-0 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028074
    Install the spring and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    B-0
    63.6 mm (2.504 in.)
    16.0 mm (0.630 in.)
    Red


39. INSTALL C-2 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028073
    Install the 2 springs and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    C-2 Inner
    42.1 mm (1.657 in.)
    14.7 mm (0.579 in.)
    Pink
    C-2 Outer
    64.0 mm (2.519 in.)
    19.7 mm (0.776 in.)
    Blue


40. INSTALL B-2 ACCUMULATOR PISTON

  1. AT05010E02
    Coat new O-rings with ATF, and install them to the piston.

  1. D028072
    Install the spring and the accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length outer diameter mm (in.)
    Color
    B-2
    70.5 mm (2.776 in.)
    19.7 mm (0.776 in.)
    Light Gray


41. INSTALL CHECK BALL BODY

  1. AT05098E02
    Install the check ball body and spring.


42. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. AT08393E02
    Align the groove of the manual valve with the pin of the lever.

  1. D029011E05
    Install the 20 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    23 mm (0.91 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    36 mm (1.42 in.)


43. INSTALL TRANSMISSION WIRE

  1. Q000625
    Coat a new O-ring with ATF, and install it to the solenoid wiring.

  1. Install the solenoid wiring to the case, and install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C058460
    Connect the connectors to each shift solenoid valve.


44. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. D005554
    Install 5 new gaskets on the oil strainer.

  1. D005550E02
    Install the oil strainer with the 4 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    14 mm (0.55 in.)
    Bolt B:
    20 mm (0.79 in.)
    Bolt C:
    23 mm (0.91 in.)


45. INSTALL TRANSMISSION OIL CLEANER MAGNET

  1. D029014E02
    Install the 3 magnets on the oil pan.


46. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. AT01362E06
    Remove any FIPG material, and be careful not to drop oil on the contacting surfaces of the transmission case and the oil pan.

  1. Apply FIPG to the oil pan.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Install the oil pan with the 19 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


47. INSTALL SENSOR ROTOR (w/o Speedometer Sensor)

  1. C114748E04
    Using a snap ring expander, install the front side snap ring.

  1. Install the key and sensor rotor.

  1. Using a snap ring expander, install the rear side snap ring.


48. INSTALL SENSOR ROTOR (w/ Speedometer Sensor)

  1. C158437E04
    Using a snap ring expander, install the snap ring.

  1. Install the key and sensor rotor.


49. INSTALL SPEEDOMETER DRIVE GEAR (w/ Speedometer Sensor)

  1. C158436E01
    Install the ball and the speedometer drive gear.

  1. Using a snap ring expander, install the snap ring.


50. INSTALL EXTENSION HOUSING DUST DEFLECTOR

  1. D005578
    Using a screwdriver and hammer, install a new extension housing dust deflector.


51. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C106499E01
    Using SST and a hammer, install a new extension housing oil seal.
    SST
    09950-60020   (09951-00580)
    09950-70010   (09951-07100)

    Oil seal in depth:
    6.0 +- 0.2 mm (0.236 +- 0.008 in.)


52. INSTALL EXTENSION HOUSING BUSH APPLY TUBE

  1. C114745E08
    Install the extension housing bush apply tube.


53. INSTALL EXTENSION HOUSING BUSH APPLY TUBE GASKET

  1. C114745E09
    Install the extension housing bush apply tube gasket.


54. INSTALL EXTENSION HOUSING SUB-ASSEMBLY

  1. C114744
    Apply seal packing or equivalent to the 6 bolts.

    Seal packing:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the extension housing and a new gasket to the case with the 6 bolts.

    Torque:
    36 N*m{ 370 kgf*cm , 27 ft.*lbf }

    HINT:
    The 2 lower bolts are shorter.


55. INSTALL AUTOMATIC TRANSMISSION HOUSING

  1. C114749
    Clean the threads of the bolts and the case with white gasoline.

  1. Apply seal packing or equivalent to the 6 bolts.

    Seal packing:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the transmission housing with the 6 bolts.

    Torque:
    14 mm bolt:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    17 mm bolt:
    57 N*m{ 580 kgf*cm , 42 ft.*lbf }


56. INSTALL SPEED SENSOR SP2

  1. C158426E01
    Coat a new O-ring with ATF, and install it onto the speed sensor SP2.

  1. Install the speed sensor SP2 with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


57. INSTALL SPEED SENSOR NC0

  1. C158425E01
    Coat a new O-ring with ATF, and install it onto the speed sensor NC0.

  1. Install the speed sensor NC0 with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


58. INSTALL SPEEDOMETER SENSOR (w/ Speedometer Sensor)

  1. C300629
    Install the speedometer driven gear to the speedometer sensor.

    HINT:
    Insert the speedometer driven gear so that the gear's grooves align with the protrusions inside the speedometer sensor.

  1. Coat a new O-ring with ATF, and install it onto the speedometer sensor.

  1. C300625E01
    Install the speedometer sensor with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


59. INSTALL OIL COOLER TUBE UNION

  1. C160268E01
    Coat 2 new O-rings with ATF, and install them onto each oil cooler tube union.

  1. Install the 2 oil cooler tube unions.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    Union installation angle:
    0° +/- 2° for Union A
    7° +/- 2° for Union B


60. INSTALL TEMPERATURE SENSOR

  1. Q003891
    Coat a new O-ring with ATF, and install it to the temperature sensor.

  1. Install the temperature sensor.

    Torque:
    15 N*m{ 152 kgf*cm , 11 ft.*lbf }


61. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C101516E03
    Install the park/neutral position switch onto the manual valve lever shaft, and temporarily tighten the adjusting bolt.

  1. Install a new lock washer, and then install the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Using the control shaft lever, fully turn the manual lever shaft back, and then return 2 notches. It is now in neutral.

  1. D006517E01
    Align the neutral basic line with the switch groove, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.


62. INSTALL BREATHER PLUG HOSE

  1. C101784
    Install the breather plug hose with the bolt.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


63. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

  1. C160267E01
    Install the transmission control shaft lever LH with the bolt.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


64. INSTALL DRAIN (ATM) PLUG SUB-ASSEMBLY

Torque:
20 N*m{ 205 kgf*cm , 15 ft.*lbf }

← INSPECTION (from Oct 2014)COMPONENTS (from Oct 2014) →