2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2015


1. REMOVE FRONT OIL PUMP BODY O-RING

  1. C321249
    Remove the front oil pump body O-ring from the oil pump assembly.


2. SECURE OIL PUMP ASSEMBLY

  1. C321250
    Place the oil pump assembly on the torque converter assembly.


3. REMOVE CLUTCH DRUM OIL SEAL RING

  1. C321251
    Remove the 2 clutch drum oil seal rings from the oil pump assembly.


4. INSPECT FRONT OIL PUMP DRIVE GEAR ROTATION
  1. Install the oil pump assembly to the torque converter assembly.

  1. C322211
    Check that the front oil pump drive gear rotates smoothly.

  1. Remove the oil pump assembly from the torque converter assembly.


5. REMOVE FRONT OIL PUMP PLATE

  1. C321252
    Using a T30 "TORX" socket wrench, remove the 3 screws and front oil pump plate from the oil pump assembly.


6. REMOVE STATOR SHAFT ASSEMBLY

  1. C321253
    Using a T30 "TORX" socket wrench, remove the 7 screws and stator shaft assembly from the front oil pump body sub-assembly.


7. INSPECT STATOR SHAFT ASSEMBLY

  1. C321258
    Using a dial indicator, measure the inside diameter of the stator shaft assembly bushing.

    Maximum inside diameter:
    22.227 mm (0.875 in.)

    If the inside diameter is more than the maximum inside diameter, replace the stator shaft assembly.


8. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY

  1. C321259
    Push the front oil pump driven gear to one side of the front oil pump body sub-assembly.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.00394 to 0.00669 in.)

    If the body clearance is more than the standard clearance, check the front oil pump drive gear, front oil pump driven gear and front oil pump body sub-assembly.

  1. C322209
    Using a feeler gauge, measure the clearance between the front oil pump driven gear teeth and the front oil pump drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.00276 to 0.00590 in.)

    If the tip clearance is more than the standard clearance, check the front oil pump drive gear, front oil pump driven gear and front oil pump body sub-assembly.

  1. C322210
    Using a steel straightedge and a feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.03 to 0.05 mm (0.00118 to 0.00196 in.)

    If the side clearance is more than the standard thickness, check the front oil pump drive gear, front oil pump driven gear and front oil pump body sub-assembly.


9. REMOVE FRONT OIL PUMP DRIVE GEAR

  1. C321254
    Remove the front oil pump drive gear from the front oil pump body sub-assembly.


10. REMOVE FRONT OIL PUMP DRIVEN GEAR

  1. C321255
    Remove the front oil pump driven gear from the front oil pump body sub-assembly.


11. REMOVE FRONT OIL PUMP OIL SEAL

  1. C321256E01
    Using a screwdriver, remove the front oil pump oil seal from the front oil pump body sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the bushing or front oil pump body sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


12. INSPECT FRONT OIL PUMP BODY SUB-ASSEMBLY

  1. C321257
    Using a dial indicator, measure the inside diameter of the front oil pump body sub-assembly bushing.

    Maximum inside diameter:
    38.138 mm (1.50 in.)

    If the inside diameter is more than the maximum inside diameter, replace the front oil pump body sub-assembly.

← COMPONENTS (from Jan 2015)INSPECTION (from Jan 2015) →