2014-2019 Hiace · Service Manual BODY ELECTRICAL

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Data List.

  5. According to the display on the GTS, read the Data List.

    HL AutoLeveling (for LED Headlight) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Headlight Low Beam State
    Low beam headlight state / ON or OFF
    ON: Low beam headlights on
    OFF: Low beam headlights off
    -
    Headlight High Beam State
    High beam headlight state / ON or OFF
    ON: High beam headlights on
    OFF: High beam headlights off
    -
    +B
    Ignition power supply voltage value / 0 to 19.75 V
    11 to 14 V
    IG ON
    Height Sens Pw Supply Val
    Rear height control sensor power supply value / 0 to 5 V
    Approximately 5.0 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value / 0 to 5 V
    Approximately 2.5 V (when vehicle level)
    The value changes according to the vehicle height.
    Vehicle Speed
    Vehicle speed / 0 to 260 km/h
    Actual vehicle speed
    -
    Rear Height Adjust Value
    Rear height adjustment offset value / 0 to 1023
    Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed)
    -
    Rear Height Adjust Valid Flag
    Result of rear vehicle height calibration / Valid or Inval
    Valid: Rear vehicle height calibration completed
    Inval: Rear vehicle height calibration not completed
    -
    Init Writing Count
    Number of times initialization performed / 0 to 255
    Current condition displayed
    -
    Sensor Initialization Hist
    Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied
    Current condition displayed
    -
    Vehicle Acceleration
    Vehicle acceleration / -445.64 to 445.63 m/s2
    Vehicle acceleration displayed
    -
    Number Of Trouble Codes
    Number of trouble codes / 0 to 255
    Condition can be displayed
    -
    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch (right turn position) signal / ON or OFF
    ON: Turn signal switch in right turn position
    OFF: Turn signal switch not in right turn position
    -
    Turn Signal Switch (Left)
    Turn signal switch (left turn position) signal / ON or OFF
    ON: Turn signal switch in left turn position
    OFF: Turn signal switch not in left turn position
    -
    Hazard Flasher Switch
    Hazard warning signal switch signal / ON or OFF
    ON: Hazard warning signal switch on
    OFF: Hazard warning signal switch off
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Body Electrical / (desired system) / Active Test.

  5. According to the display on the GTS, perform the Active Test.

    HL AutoLeveling (for LED Headlight) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor
    Leveling motor upward or downward operation
    Stop/Down/Up
    Perform the Active Test with the engine started and vehicle stopped.
    Entry&Start (w/ Smart Entry and Start System) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power/Engine SW Light
    Engine switch illumination
    ON/OFF
    -

← FAIL-SAFE CHART (from Oct 2014)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →