2014-2019 Hiace · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Oct 2014


CHECK ENGINE SWITCH
B268088E11
  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I32-6 (AGND) - Body ground
    -
    V - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    -
    I32-7 (TXCT) - I32-6 (AGND)
    Input
    L - V
    Immobiliser communication input
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I32-8 (CODE) - I32-6 (AGND)
    Output
    G - V
    Immobiliser communication output
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I32-10 (VC5) - I32-6 (AGND)
    Input
    B - V
    Transponder key amplifier power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -

  2. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I32-7 (TXCT) - I32-6 (AGND)
    Input
    L - V
    Signal input from certification ECU (smart key ECU assembly)
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response

      HINT:
      If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above

    I32-8 (CODE) - I32-6 (AGND)
    Output
    G - V
    Signal output to certification ECU (smart key ECU assembly)
    (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Engine switch off, engine switch pressed with key held near engine switch*
    Pulse generation
    (See waveform 2)
    I32-10 (VC5) - I32-6 (AGND)
    Input
    B - V
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)

    HINT:
    *: Remove the key battery before performing this inspection.

  3. Using an oscilloscope, check the waveform.

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. B051052E14
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I32-7 (TXCT) - I32-6 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

    2. B345737E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I32-8 (CODE) - I32-6 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, engine switch pressed with key held near engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    3. B216007E01
      Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I32-10 (VC5) - I32-6 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B333750E03
  1. Disconnect the B75 and B76 certification ECU (smart key ECU assembly) connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    B75-1 (+B) - B75-10 (E)
    Input
    L - W-B
    +B power supply
    Always
    11 to 14 V
    -
    B75-10 (E) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -

  3. Reconnect the B75 and B76 certification ECU (smart key ECU assembly) connectors.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    B75-15 (IND) - B75-10 (E)
    Output
    L - W-B
    Security indicator output
    Engine switch off → on (IG)
    Pulse generation
    → Below 2 V
    -
    B76-2 (TXCT) - B75-24 (AGND)
    Output
    L - V
    Signal output to transponder key amplifier
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    B76-1 (CODE) - B75-24 (AGND)
    Input
    G - V
    Signal input from transponder key amplifier
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    B76-20 (VC5) - B75-24 (AGND)
    Output
    B - V
    Transponder key amplifier power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    B75-24 (AGND) - Body ground
    -
    V - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω

  5. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    B76-2 (TXCT) - B75-24 (AGND)
    Output
    L - V
    Signal output to transponder key amplifier
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    B76-1 (CODE) - B75-24 (AGND)
    Input
    G - V
    Signal input from transponder key amplifier
    (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Engine switch off, engine switch pressed with key held near engine switch*
    Pulse generation
    (See waveform 2)
    B76-20 (VC5) - B75-24 (AGND)
    Output
    B - V
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)

    HINT:
    *: Remove the key battery before performing this inspection.

  6. Using an oscilloscope, check the waveform.

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. B051052E14
      Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      B76-2 (TXCT) - B75-24 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

    2. B345737E01
      Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      B76-1 (CODE) - B75-24 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, engine switch pressed with key held near engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.

    3. B216007E01
      Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      B76-20 (VC5) - B75-24 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
B269095E02
  1. Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    H80-1 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    H80-3 (IGE) - H80-1 (GND)
    Input
    V - W-B
    Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly))
    Steering lock motor operates when both conditions met, and then door opened:
    1. Shift lever in P
    2. Key carried, engine switch turned on (IG), steering unlocked and then engine switch turned off
    Pulse generation
    (See waveform 1)
    1. Power Supply Short
    2. Unlock Request Receive
    3. Lock Request Receive
    H80-4 (SLP1) - H80-1 (GND)
    Output
    LG - W-B
    Steering lock bar position signal (signal output from steering unlock sensor)
    Steering locked → unlocked*
    11 to 14 V → Below 1.5 V
    1. Push Start Error
    2. Sensor Value
    H80-6 (IG2) - H80-1 (GND)
    Input
    B - W-B
    IG signal (IG2 power supply input for steering lock motor)
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    B2788
    H80-7 (B) - Body ground
    Output
    W - Body ground
    Constant power supply
    Always
    11 to 14 V
    B2788

    HINT:
    *: The steering locks when any door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).

  2. Using an oscilloscope, check the waveform.

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. C221561E01
      Waveform 1 (Reference)
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating
      Measurement Condition 
      Item
      Content
      Tester Connection
      H80-3 (IGE) - H80-1 (GND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Steering lock motor operates when both conditions met, and then door opened:
      1. Shift lever in P
      2. Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


CHECK ID CODE BOX (IMMOBILISER CODE ECU)
B302477E04
  1. Disconnect the H81 ID code box (immobiliser code ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    H81-1 (+B) - H81-5 (GND)
    Input
    W - W-B
    +B power supply
    Always
    11 to 14 V
    B2789
    H81-5 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B2789

  3. Reconnect the H81 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    H81-3 (EFII) - H81-5 (GND)
    Input
    R - W-B
    EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU))
    Engine switch off
    Below 1 V
    1. B2799
    2. B279A
    3. Engine Start Request
    4. EFI Code Receiver
    H81-3 (EFII) - H81-5 (GND)
    Input
    R - W-B
    EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU))
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    H81-4 (EFIO) - H81-5 (GND)
    Output
    B - W-B
    EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM)
    Engine switch off
    Below 1 V
    H81-4 (EFIO) - H81-5 (GND)
    Output
    B - W-B
    EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM)
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)

  5. Using an oscilloscope, check the waveform.

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. Waveform 1 (Reference)
      B278942E01

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      H81-3 (EFII) - H81-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    2. Waveform 2 (Reference)
      B278943E01

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      H81-4 (EFIO) - H81-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


CHECK ECM
B366723E07
  1. Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    B72-20 (+B2) - D98-109 (E1)
    Input
    L - W-B
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    -
    B72-1 (+B) - D98-109 (E1)
    Input
    L - W-B
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    -
    B72-2 (BATT) - D98-109 (E1)
    Input
    W - W-B
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    -
    D98-109 (E1) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    B72-15 (IMO) - D98-109 (E1)
    Input
    R - W-B
    Certification ECU (smart key ECU assembly) communication input
    Engine switch off
    11 to 14 V
    -
    B72-15 (IMO) - D98-109 (E1)
    Input
    R - W-B
    Certification ECU (smart key ECU assembly) communication input
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    -
    B72-16 (IMI) - D98-109 (E1)
    Output
    B - W-B
    Certification ECU (smart key ECU assembly) communication output
    Engine switch off
    Below 1 V
    -
    B72-16 (IMI) - D98-109 (E1)
    Output
    B - W-B
    Certification ECU (smart key ECU assembly) communication output
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)
    -

  2. Using an oscilloscope, check the waveform.

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


    1. Waveform 1 (Reference)
      B278942E01

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      B72-15 (IMO) - D98-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

    2. Waveform 2 (Reference)
      B278943E01

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      B72-16 (IMI) - D98-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected

← PROBLEM SYMPTOMS TABLE (from Dec 2017)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →