P0560/96 System Voltage
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2016
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
DESCRIPTION
The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and etc. If the battery voltage falls below a minimum level, the stored data is cleared and the TCM determines that there is a malfunction in the power supply circuit. When the engine is next started, the TCM will illuminate the MIL and set the DTC.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0560/96 |
Open in TCM back-up power source circuit. DTC is detected for 3 sec. or more. (1-trip detection logic) |
|
- HINT:
- If DTC P0560/96 is set, the TCM does not store other DTCs.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FUSE (EFI NO. 2 FUSE) |
Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.

Measure the EFI NO. 2 fuse resistance.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (BATT VOLTAGE OF TCM) |
Disconnect the TCM connector.
Measure the voltage of the TCM connector.

- Standard voltage:
Tester Connection
Specified Condition
BATT (O3-5) - Body ground
11 to 14 V
|
|
||||
| OK | |
| 3. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Clear the DTC (Click here).
Turn the ignition switch off and turn the tester off.
Start the engine and turn on the tester.
Select the item: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
- Result:
Display (DTC output)
Proceed to
P0560/96
A
No DTC
B
- HINT:
- When not using the intelligent tester, refer to DTC CHECK / CLEAR (Click here).
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND, TCM - EFI NO. 2 FUSE - BATTERY) |
Check the harness and the connector between the TCM and body ground.

Disconnect the TCM connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
E1 (O1-1) - Body ground
Below 1 Ω
Check the harness and the connector between the EFI NO. 2 fuse and TCM.


Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.
Disconnect the TCM connector.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
EFI NO. 2 fuse (2) - BATT (O3-5)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
EFI NO. 2 fuse (2) or BATT (O3-5) - Body ground
10 kΩ or higher
Check the harness and the connector between the EFI NO. 2 fuse and battery.
Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.
Disconnect the negative battery terminal.
Disconnect the positive battery terminal.
Measure the resistance.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
Battery positive terminal - EFI NO. 2 fuse (1)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
Battery positive terminal or EFI NO. 2 fuse (1) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT BATTERY |
Check that the battery is not depleted.
- OK:
- Battery is not depleted
|
|
||||
| OK | |
| 6. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Clear the DTC (Click here).
Turn the ignition switch off and turn the tester off.
Start the engine and turn on the tester.
Select the item: "Powertrain / ECT / DTC / Current or Pending".
Read the DTCs using the intelligent tester.
- Result:
Display (DTC output)
Proceed to
P0560/96
A
No DTC
B
- HINT:
- When not using the intelligent tester, refer to DTC CHECK / CLEAR (Click here).
|
|
||||
| A | ||
| ||
