2014-2019 Hiace · Service Manual TRANSMISSION

P0560/96 System Voltage

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017

DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and etc. If the battery voltage falls below a minimum level, the stored data is cleared and the TCM determines that there is a malfunction in the power supply circuit. When the engine is next started, the TCM will illuminate the MIL and set the DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0560/96
Open in TCM back-up power source circuit.
DTC is detected for 3 sec. or more.
(1-trip detection logic)
  1. Open in TCM back-up power source circuit
  2. EFI NO. 2 fuse
  3. Battery
  4. TCM

HINT:
If DTC P0560/96 is set, the TCM does not store other DTCs.


WIRING DIAGRAM

C301988E01

INSPECTION PROCEDURE


1. CHECK FUSE (EFI NO. 2 FUSE)

  1. C301989E01
    Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.

  1. Measure the EFI NO. 2 fuse resistance.

    Standard resistance:
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (BATT VOLTAGE OF TCM)
  1. Disconnect the TCM connector.

  1. G037243E14
    Measure the voltage of the TCM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    BATT (O3-5) - Body ground
    11 to 14 V



NG
Go to step 4
OK


3. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn on the tester.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and turn the tester off.

  1. Start the engine and turn on the tester.

  1. Select the item: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    P0560/96
    A
    No DTC
    B

    HINT:
    When not using the intelligent tester, refer to DTC CHECK / CLEAR (Click here).



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE TCM

4. CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND, TCM - EFI NO. 2 FUSE - BATTERY)

  1. F045523E42
    Check the harness and the connector between the TCM and body ground.
    1. Disconnect the TCM connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      E1 (O1-1) - Body ground
      Below 1 Ω

  1. Check the harness and the connector between the EFI NO. 2 fuse and TCM.C302206E01

    1. Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.

    2. Disconnect the TCM connector.

    3. Measure the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      EFI NO. 2 fuse (2) - BATT (O3-5)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      EFI NO. 2 fuse (2) or BATT (O3-5) - Body ground
      10 kΩ or higher

  1. Check the harness and the connector between the EFI NO. 2 fuse and battery.

    1. Remove the EFI NO. 2 fuse from the No. 1 engine room relay block and junction block assembly.

    2. Disconnect the negative battery terminal.

    3. Disconnect the positive battery terminal.

    4. Measure the resistance.

      Standard resistance (Check for open):
      Tester Connection
      Specified Condition
      Battery positive terminal - EFI NO. 2 fuse (1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Specified Condition
      Battery positive terminal or EFI NO. 2 fuse (1) - Body ground
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted



NG
REPLACE BATTERY
OK


6. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn on the tester.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and turn the tester off.

  1. Start the engine and turn on the tester.

  1. Select the item: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    P0560/96
    A
    No DTC
    B

    HINT:
    When not using the intelligent tester, refer to DTC CHECK / CLEAR (Click here).



B
CHECK FOR INTERMITTENT PROBLEMS
A

REPLACE TCM


← P0560/96 System Voltage (Oct 2014 – Dec 2016)P0617 Starter Relay Circuit High (from Oct 2014) →