2014-2019 Hiace · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from ECM causes a current to flow to the coil, closing the contacts of the EFI MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A319603E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance::
    Tester Connection
    Condition
    Specified Condition
    B98-109 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE)

  1. A204368E26
    Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B72-25 (IGSW) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

Result 
Result
Proceed to
OK
A
NG (w/o Smart Entry and Start System)
B
NG (w/ Smart Entry and Start System)
C


B
Go to step 5

C
Go to step 6
A


3. INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN)
  1. Inspect the No. 1 integration relay (EFI MAIN) (Click here).



NG
REPLACE INTEGRATION NO. 1 RELAY (EFI MAIN)
OK


4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Check the harness and connector between the No. 1 integration relay (EFI MAIN) and ECM.

    1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      10B-4 - B72-20 (+B2)
      Always
      Below 1 Ω
      10B-4 - B72-1 (+B)
      Always
      Below 1 Ω
      10B-2 - B72-45 (MREL)
      Always
      Below 1 Ω
      10B-4 or B72-20 (+B2) - Body ground
      Always
      10 kΩ or higher
      10B-4 or B72-1 (+B) - Body ground
      Always
      10 kΩ or higher
      10B-2 or B72-45 (MREL) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reinstall the No. 1 integration relay.

  1. Check the harness and connector between the No. 1 integration relay (EFI MAIN) and body ground.

    1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      10B-3 - Body ground
      Always
      Below 1 Ω

    3. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN RELAY)

5. INSPECT IGNITION SWITCH
  1. Inspect the ignition switch (Click here).



NG
REPLACE IGNITION SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

6. CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - SMART KEY ECU)
  1. Disconnect the smart key ECU connector.

  1. Remove the No. 2 integration relay from the instrument panel relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12D-2 - B75-20 (IG1D)
    Always
    Below 1 Ω
    12D-2 or B75-20 (IG1D) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the smart key ECU connector.

  1. Reinstall the No. 2 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 INTEGRATION RELAY - SMART KEY ECU)
OK

CHECK ENTRY AND START SYSTEM


← Turbocharger Noise (from Jan 2017)ECM Power Source Circuit (Jan 2015 – Nov 2015) →