P0200 Injector Circuit / Open
Diagnostic trouble codes · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The EDU drives the injectors at high speeds. The EDU delivers high-speed driving under highly-pressurized fuel conditions using the DC/DC converter, which provides a high-voltage and quick-charging system.Soon after the EDU receives an injection command (#1 to #4) signal from the ECM, the EDU responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 5 seconds |
Open or short in EDU or injector circuit After engine is started, there is no INJF signal from EDU to ECM, despite ECM sending #1 to #4 signal to EDU (1 trip detection logic) |
|
- HINT:
- DTC P0200 is detected when start the engine and let it idle for 30 seconds.
MONITOR DESCRIPTION
- P0200 (Open or short in EDU or injector circuit):
The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signal. This DTC will be set if the ECM judges that the number of #1 to #4 signals and INJF signals are inconsistent.
The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit), in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
P0200/97 refers to a malfunction in the EDU or injector circuit.
If this DTC is set, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned OFF.


MONITOR STRATEGY
| Required sensors |
INJF signal from EDU |
| Frequency of operation |
Continuous |
| Duration |
10 seconds |
| MIL operation |
1 driving cycle |
TYPICAL ENABLING CONDITIONS
| Item |
Specification |
Specification |
| Minimum |
Maximum |
|
| Engine speed |
500 rpm |
- |
| Battery voltage |
11 V |
- |
| Igniton switch |
ON |
ON |
TYPICAL MALFUNCTION THRESHOLDS
| Threshold |
| The injection missing counter* for all the cylinders, or for one individual cylinder, reaches a specified number (taking approximately 1 second after starting the engine) *: Increments when no INJF signal is received from the EDU despite the ECM sending #1 to #4 signals |
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the injector, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK ENGINE CRANKING CONDITION |
Check the engine cranking condition.
Result Result
Proceed to
Engine does not start*1
A
Engine starts, but idling is rough*2
B
Except above
C
- HINT:
- *1: Once DTC P0200 is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Common Rail Pressure" is higher than the value for "Target Common Rail Pressure"
- *2: DTC P0200 is stored at this time.
- *1: Once DTC P0200 is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
|
|
||||
|
|
||||
| A | |
| 2. CHECK ECM |
Disconnect the injector driver (EDU) connector.
Check the waveform of the injector driver (EDU) connectors using an oscilloscope while cranking the engine.

- OK:
Tester Connection
Condition
Specified Condition
B15-6 (#10) - B15-1 (GND)
Cranking
Correct waveform is as shown
B15-3 (#20) - B15-1 (GND)
Cranking
Correct waveform is as shown
B15-2 (#30) - B15-1 (GND)
Cranking
Correct waveform is as shown
B15-5 (#40) - B15-1 (GND)
Cranking
Correct waveform is as shown
Text in Illustration *a
Front view of wire harness connector
(to Injector Driver (EDU))
Reconnect the injector driver connectors.
|
|
||||
| OK | |
| 3. CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE |
Disconnect the injector driver connectors.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B13-8 (+B) - B15-1 (GND)
Ignition switch ON
9 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Injector Driver (EDU))
Reconnect the injector driver connectors.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM) |
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B15-6 (#10) - D105-50 (#1)
Always
Below 1 Ω
B15-3 (#20) - D105-49 (#2)
Always
Below 1 Ω
B15-2 (#30) - D105-48 (#3)
Always
Below 1 Ω
B15-5 (#40) - D105-47 (#4)
Always
Below 1 Ω
B15-7 (INJF) - D105-51 (INJF)
Always
Below 1 Ω
B15-6 (#10) or D105-50 (#1) - Body ground
Always
10 kΩ or higher
B15-3 (#20) or D105-49 (#2) - Body ground
Always
10 kΩ or higher
B15-2 (#30) or D105-48 (#3) - Body ground
Always
10 kΩ or higher
B15-5 (#40) or D105-47 (#4) - Body ground
Always
10 kΩ or higher
B15-7 (INJF) or D105-51 (INJF) - Body ground
Always
10 kΩ or higher
Reconnect the injector driver connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 5. REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
|
|
||||
| 6. READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 to #4) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
Start the engine.
Read the Injection Feedback Val #1 to #4 values while idling the engine.
- Standard Value:
Item
Engine Speed*
Reference Value
Injection Feedback Val #1 to #4
Idling
+3.0 mm3/st or less
- HINT:
- *: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
- Fuel is not being injected in cylinders whose "Injection Feedback Val" is higher than 3 mm3/st. Inspection procedures beyond this point diagnose whether there are internal problems with fuel injectors, or whether there is a problem in the wiring of the fuel injector system.
- *: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
| NEXT | |
| 7. INSPECT INJECTOR ASSEMBLY (RESISTANCE) |
Disconnect the fuel injector connectors.

Measure the resistance of the fuel injector
- OK:
- No open or short circuit malfunction.
Text in Illustration *a
Component with harness connected
(Fuel injector)
Reconnect the fuel injector connectors.
|
|
||||
| OK | |
| 8. INSPECT INJECTOR DRIVER |
Disconnect the fuel injector connectors for all cylinders.

Check the waveform of the fuel injector connectors using an oscilloscope.
- OK:
Tester Connection
Condition
Specified Condition
D24-1 - D24-2
Cranking
Voltage increases by 50 V or more
D25-1 - D25-2
Cranking
Voltage increases by 50 V or more
D26-1 - D26-2
Cranking
Voltage increases by 50 V or more
D27-1 - D27-2
Cranking
Voltage increases by 50 V or more
Text in Illustration *a
Front view of wire harness connector
(to Fuel injector)
|
|
||||
| OK | |
| 9. REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly (Click here).
- NOTICE:
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
- Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
- If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
- If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
- If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
- When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
| NEXT | |
| 10. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 11. REGISTER INJECTOR COMPENSATION CODE |
Register the injector compensation code (Click here).
|
|
||||
| 12. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM) |
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B15-6 (#10) - D105-50 (#1)
Always
Below 1 Ω
B15-3 (#20) - D105-49 (#2)
Always
Below 1 Ω
B15-2 (#30) - D105-48 (#3)
Always
Below 1 Ω
B15-5 (#40) - D105-47 (#4)
Always
Below 1 Ω
B15-7 (INJF) - D105-51 (INJF)
Always
Below 1 Ω
B15-6 (#10) or D105-50 (#1) - Body ground
Always
10 kΩ or higher
B15-3 (#20) or D105-49 (#2) - Body ground
Always
10 kΩ or higher
B15-2 (#30) or D105-48 (#3) - Body ground
Always
10 kΩ or higher
B15-5 (#40) or D105-47 (#4) - Body ground
Always
10 kΩ or higher
B15-7 (INJF) or D105-51 (INJF) - Body ground
Always
10 kΩ or higher
Reconnect the injector driver connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 13. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 14. CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER) |
Disconnect the injector assembly connectors.

Disconnect the injector driver connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D24-2 - B13-4 (INJ1)
Always
Below 1 Ω
D25-2 - B13-2 (INJ2)
Always
Below 1 Ω
D26-2 - B13-1 (INJ3)
Always
Below 1 Ω
D27-2 - B13-3 (INJ4)
Always
Below 1 Ω
D24-1 - B13-5 (COM1)
Always
Below 1 Ω
D25-1 - B13-6 (COM2)
Always
Below 1 Ω
D26-1 - B13-6 (COM2)
Always
Below 1 Ω
D27-1 - B13-5 (COM1)
Always
Below 1 Ω
D24-2 or B13-4 (INJ1) - Body ground
Always
10 kΩ or higher
D25-2 or B13-2 (INJ2) - Body ground
Always
10 kΩ or higher
D26-2 or B13-1 (INJ3) - Body ground
Always
10 kΩ or higher
D27-2 or B13-3 (INJ4) - Body ground
Always
10 kΩ or higher
D24-1 or B13-5 (COM1) - Body ground
Always
10 kΩ or higher
D25-1 or B13-6 (COM2) - Body ground
Always
10 kΩ or higher
D26-1 or B13-6 (COM2) - Body ground
Always
10 kΩ or higher
D27-1 or B13-5 (COM1) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Injector assembly)
*b
Front view of wire harness connector
(to Injector driver)
Reconnect the injector assembly connectors.
Reconnect the injector driver connectors.
|
|
||||
| OK | |
| 15. REPLACE INJECTOR DRIVER |
Replace the injector driver (Click here).
|
|
||||
| 16. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 17. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
