2014-2019 Hiace · Service Manual ENGINE

P0200 Injector Circuit / Open

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The EDU drives the injectors at high speeds. The EDU delivers high-speed driving under highly-pressurized fuel conditions using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the EDU receives an injection command (#1 to #4) signal from the ECM, the EDU responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector.
A099226E11
P0200 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 seconds
Open or short in EDU or injector circuit
After engine is started, there is no INJF signal from EDU to ECM, despite ECM sending #1 to #4 signal to EDU
(1 trip detection logic)
  1. Open or short in EDU circuit
  2. Injector
  3. EDU
  4. ECM

HINT:
DTC P0200 is detected when start the engine and let it idle for 30 seconds.


MONITOR DESCRIPTION

  1. P0200 (Open or short in EDU or injector circuit):
    The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signal. This DTC will be set if the ECM judges that the number of #1 to #4 signals and INJF signals are inconsistent.
    The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit), in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
    P0200/97 refers to a malfunction in the EDU or injector circuit.
    If this DTC is set, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned OFF.
A145849E13

MONITOR STRATEGY

Required sensors
INJF signal from EDU
Frequency of operation
Continuous
Duration
10 seconds
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS

Item
Specification
Specification

Minimum
Maximum
Engine speed
500 rpm
-
Battery voltage
11 V
-
Igniton switch
ON
ON

TYPICAL MALFUNCTION THRESHOLDS

Threshold
The injection missing counter* for all the cylinders, or for one individual cylinder, reaches a specified number (taking approximately 1 second after starting the engine)
*: Increments when no INJF signal is received from the EDU despite the ECM sending #1 to #4 signals

WIRING DIAGRAM

A319084E01
A319085E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the injector, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Engine does not start*1
    A
    Engine starts, but idling is rough*2
    B
    Except above
    C

    HINT:
    1. *1: Once DTC P0200 is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
      When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Common Rail Pressure" is higher than the value for "Target Common Rail Pressure"
    2. *2: DTC P0200 is stored at this time.



B
Go to step 6

C
CHECK INTERMITTENT PROBLEMS
A


2. CHECK ECM
  1. Disconnect the injector driver (EDU) connector.

  1. A317502E01
    Check the waveform of the injector driver (EDU) connectors using an oscilloscope while cranking the engine.

    OK:
    Tester Connection
    Condition
    Specified Condition
    B15-6 (#10) - B15-1 (GND)
    Cranking
    Correct waveform is as shown
    B15-3 (#20) - B15-1 (GND)
    Cranking
    Correct waveform is as shown
    B15-2 (#30) - B15-1 (GND)
    Cranking
    Correct waveform is as shown
    B15-5 (#40) - B15-1 (GND)
    Cranking
    Correct waveform is as shown
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver (EDU))

  1. Reconnect the injector driver connectors.



NG
Go to step 12
OK


3. CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE

  1. A099850E12
    Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B13-8 (+B) - B15-1 (GND)
    Ignition switch ON
    9 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver (EDU))

  1. Reconnect the injector driver connectors.



NG
Go to step 16
OK


4. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
  1. Disconnect the injector driver connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B15-6 (#10) - D105-50 (#1)
    Always
    Below 1 Ω
    B15-3 (#20) - D105-49 (#2)
    Always
    Below 1 Ω
    B15-2 (#30) - D105-48 (#3)
    Always
    Below 1 Ω
    B15-5 (#40) - D105-47 (#4)
    Always
    Below 1 Ω
    B15-7 (INJF) - D105-51 (INJF)
    Always
    Below 1 Ω
    B15-6 (#10) or D105-50 (#1) - Body ground
    Always
    10 kΩ or higher
    B15-3 (#20) or D105-49 (#2) - Body ground
    Always
    10 kΩ or higher
    B15-2 (#30) or D105-48 (#3) - Body ground
    Always
    10 kΩ or higher
    B15-5 (#40) or D105-47 (#4) - Body ground
    Always
    10 kΩ or higher
    B15-7 (INJF) or D105-51 (INJF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reconnect the ECM connector.



NG
Go to step 16
OK


5. REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 17
6. READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 to #4)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

  1. Start the engine.

  1. Read the Injection Feedback Val #1 to #4 values while idling the engine.

    Standard Value:
    Item
    Engine Speed*
    Reference Value
    Injection Feedback Val #1 to #4
    Idling
    +3.0 mm3/st or less

    HINT:
    1. *: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
    2. Fuel is not being injected in cylinders whose "Injection Feedback Val" is higher than 3 mm3/st. Inspection procedures beyond this point diagnose whether there are internal problems with fuel injectors, or whether there is a problem in the wiring of the fuel injector system.


NEXT


7. INSPECT INJECTOR ASSEMBLY (RESISTANCE)

  1. A191333E09
    Disconnect the fuel injector connectors.

  1. Measure the resistance of the fuel injector

    OK:
    No open or short circuit malfunction.

    Text in Illustration 
    *a
    Component with harness connected
    (Fuel injector)

  1. Reconnect the fuel injector connectors.



NG
Go to step 9
OK


8. INSPECT INJECTOR DRIVER

  1. A262670E11
    Disconnect the fuel injector connectors for all cylinders.

  1. Check the waveform of the fuel injector connectors using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    D24-1 - D24-2
    Cranking
    Voltage increases by 50 V or more
    D25-1 - D25-2
    Cranking
    Voltage increases by 50 V or more
    D26-1 - D26-2
    Cranking
    Voltage increases by 50 V or more
    D27-1 - D27-2
    Cranking
    Voltage increases by 50 V or more

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel injector)



NG
Go to step 14
OK


9. REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
  1. Replace the injector assembly (Click here).

    NOTICE:
    1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
    2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.


NEXT


10. BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system (Click here).


NEXT


11. REGISTER INJECTOR COMPENSATION CODE
  1. Register the injector compensation code (Click here).



NEXT
Go to step 17
12. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
  1. Disconnect the injector driver connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B15-6 (#10) - D105-50 (#1)
    Always
    Below 1 Ω
    B15-3 (#20) - D105-49 (#2)
    Always
    Below 1 Ω
    B15-2 (#30) - D105-48 (#3)
    Always
    Below 1 Ω
    B15-5 (#40) - D105-47 (#4)
    Always
    Below 1 Ω
    B15-7 (INJF) - D105-51 (INJF)
    Always
    Below 1 Ω
    B15-6 (#10) or D105-50 (#1) - Body ground
    Always
    10 kΩ or higher
    B15-3 (#20) or D105-49 (#2) - Body ground
    Always
    10 kΩ or higher
    B15-2 (#30) or D105-48 (#3) - Body ground
    Always
    10 kΩ or higher
    B15-5 (#40) or D105-47 (#4) - Body ground
    Always
    10 kΩ or higher
    B15-7 (INJF) or D105-51 (INJF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reconnect the ECM connector.



NG
Go to step 16
OK


13. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 17
14. CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)

  1. A099847E18
    Disconnect the injector assembly connectors.

  1. Disconnect the injector driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D24-2 - B13-4 (INJ1)
    Always
    Below 1 Ω
    D25-2 - B13-2 (INJ2)
    Always
    Below 1 Ω
    D26-2 - B13-1 (INJ3)
    Always
    Below 1 Ω
    D27-2 - B13-3 (INJ4)
    Always
    Below 1 Ω
    D24-1 - B13-5 (COM1)
    Always
    Below 1 Ω
    D25-1 - B13-6 (COM2)
    Always
    Below 1 Ω
    D26-1 - B13-6 (COM2)
    Always
    Below 1 Ω
    D27-1 - B13-5 (COM1)
    Always
    Below 1 Ω
    D24-2 or B13-4 (INJ1) - Body ground
    Always
    10 kΩ or higher
    D25-2 or B13-2 (INJ2) - Body ground
    Always
    10 kΩ or higher
    D26-2 or B13-1 (INJ3) - Body ground
    Always
    10 kΩ or higher
    D27-2 or B13-3 (INJ4) - Body ground
    Always
    10 kΩ or higher
    D24-1 or B13-5 (COM1) - Body ground
    Always
    10 kΩ or higher
    D25-1 or B13-6 (COM2) - Body ground
    Always
    10 kΩ or higher
    D26-1 or B13-6 (COM2) - Body ground
    Always
    10 kΩ or higher
    D27-1 or B13-5 (COM1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector assembly)
    *b
    Front view of wire harness connector
    (to Injector driver)

  1. Reconnect the injector assembly connectors.

  1. Reconnect the injector driver connectors.



NG
Go to step 16
OK


15. REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 17
16. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


17. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 10 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0200 Injector Circuit / Open (Oct 2014 – Dec 2014)P0200 Injector Circuit / Open (Apr 2016 – Dec 2016) →