B278A Short to GND in Immobiliser System Power Source Circuit
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016
DESCRIPTION
When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B278A |
A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*1). |
|
With the shift lever in P, the key is held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted. |
- *1: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
| Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P |
- |
| DTC Code |
Data List and Active Test |
| B278A |
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
- When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Using an oscilloscope, check the waveform.

- HINT:
- Perform this inspection on the engine switch side.
Measurement Condition Item
Content
Tester Connection
I32-10 (VC5) - I32-6 (AGND)
Tool Setting
2 V/DIV., 200 ms./DIV.
Condition
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
- OK:
- The waveform is similar to that shown in the illustration.
Text in Illustration *a
Component with harness connected
(Engine Switch)
|
|
||||
| OK | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH) |
Disconnect the B75 and B76 certification ECU (smart key ECU assembly) connectors.
Disconnect the I32 engine switch connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B76-20 (VC5) - I32-10 (VC5)
Always
Below 1 Ω
B75-24 (AGND) - I32-6 (AGND)
Always
Below 1 Ω
I32-10 (VC5) - Body ground
Always
10 kΩ or higher
B76-20 (VC5) - Body ground
Always
10 kΩ or higher
I32-6 (AGND) - Body ground
Always
10 kΩ or higher
B75-24 (AGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Connect the B75 and B76 certification ECU (smart key ECU assembly) connectors.
Connect the I32 engine switch connector.


Text in Illustration *a
Component with harness connector
(Certification ECU [Smart Key ECU Assembly])
-
-
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B76-20 (VC5) - B75-24 (AGND)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
Below 1 V
|
|
||||
| OK | ||
| ||
