2014-2019 Hiace · Service Manual SECURITIES

B278A Short to GND in Immobiliser System Power Source Circuit

Diagnostic trouble codes · Vehicles built from Apr 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016

DESCRIPTION

When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B278A
A short to GND in the power supply of the transponder key amplifier of the engine switch (VC5 - VC5) (1 trip detection logic*1).
  1. Engine switch
  2. Harness or connector
  3. Certification ECU (smart key ECU assembly)
With the shift lever in P, the key is held near the engine switch and an engine start operation is performed by pressing and holding the engine switch when the key battery is depleted.
  1. *1: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started when key battery is depleted by holding key near engine switch and pressing and holding engine switch with shift lever in P
-
Related Data List and Active Test 
DTC Code
Data List and Active Test
B278A
-

WIRING DIAGRAM

E271703E02

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
  3. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."


1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  1. B271009E13
    Using an oscilloscope, check the waveform.

    HINT:
    Perform this inspection on the engine switch side.

    Measurement Condition 
    Item
    Content
    Tester Connection
    I32-10 (VC5) - I32-6 (AGND)
    Tool Setting
    2 V/DIV., 200 ms./DIV.
    Condition
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed

    OK:
    The waveform is similar to that shown in the illustration.

    Text in Illustration 
    *a
    Component with harness connected
    (Engine Switch)



NG
Go to step 2
OK

REPLACE ENGINE SWITCH (Click here)

2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - ENGINE SWITCH)
  1. Disconnect the B75 and B76 certification ECU (smart key ECU assembly) connectors.

  1. Disconnect the I32 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B76-20 (VC5) - I32-10 (VC5)
    Always
    Below 1 Ω
    B75-24 (AGND) - I32-6 (AGND)
    Always
    Below 1 Ω
    I32-10 (VC5) - Body ground
    Always
    10 kΩ or higher
    B76-20 (VC5) - Body ground
    Always
    10 kΩ or higher
    I32-6 (AGND) - Body ground
    Always
    10 kΩ or higher
    B75-24 (AGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Connect the B75 and B76 certification ECU (smart key ECU assembly) connectors.

  1. Connect the I32 engine switch connector.B342590E02

    Text in Illustration 
    *a
    Component with harness connector
    (Certification ECU [Smart Key ECU Assembly])
    -
    -

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B76-20 (VC5) - B75-24 (AGND)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Below 1 V



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE ENGINE SWITCH (Click here)


← B278A Short to GND in Immobiliser System Power Source Circuit (Jan 2015 – Mar 2016)B2790 ID BOX EEPROM Malfunction (from Oct 2014) →