2014-2019 Hiace · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


1. INSTALL BRAKE MASTER CYLINDER

HINT:
When installing the brake master cylinder, the brake booster push rod does not need to be adjusted.

  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. for 1KD-FTV, 2KD-FTV and 5L-E:

    1. Install the brake master cylinder and bracket to the booster with the 2 nuts.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }

      NOTICE:
      Check that the stopper of the harness clamp bracket is securely holding on the brake master cylinder assembly.

  1. for 1TR-FE, 2TR-FE:

    1. Install the brake master cylinder to the brake booster with the 2 nuts.

      Torque:
      13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. for Manual Transmission:

    1. Connect the clutch tube to the brake master cylinder reservoir sub-assembly with the clip.

  1. w/o VSC:

    1. A329093E05
      Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder.

      Torque:
      Specified tightening torque:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }

      Text in Illustration 
      *a
      Torque Wrench Fulcrum Length

      HINT:
      1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
      2. When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.*lbf)

  1. w/ VSC:

    1. A329093E05
      Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder.

      Torque:
      Specified tightening torque:
      25 N*m{ 255 kgf*cm , 18 ft.*lbf }

      Text in Illustration 
      *a
      Torque Wrench Fulcrum Length

      HINT:
      1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
      2. When using a union nut wrench (fulcrum length of 20 mm (0.7874 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 23 N*m (229 kgf*cm, 17 ft.*lbf)

  1. Connect the level warning light switch connector.

  1. Attach the brake fluid level warning switch connector clamp.


2. ADD BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3 or equivalent

NOTICE:
Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.


3. BLEED BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

  1. C106089
    Using a union nut wrench, disconnect the brake lines from the master cylinder.

  1. Slowly depress the brake pedal and hold it there.

  1. C106090
    Block the outer holes with your fingers, and release the brake pedal.

  1. Remove your fingers. Slowly depress the brake pedal and hold it again. Block the outer holes with your fingers and release the brake pedal. Repeat this procedure 3 or 4 times.

  1. A329093E01
    Using a union nut wrench, connect the brake lines to the master cylinder.

    Torque:
    Specified tightening torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
    2. When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.*lbf)


4. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


5. CHECK BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No.116 DOT3 or equivalent

    NOTICE:
    Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.


6. CHECK BRAKE FLUID LEAKAGE
← INSTALLATION (Jan 2015 – Dec 2016)COMPONENTS (Oct 2014 – Dec 2014) →