2014-2019 Hiace · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


1. TEMPORARILY TIGHTEN REAR DRUM BRAKE BLEEDER PLUG

2. INSTALL REAR WHEEL BRAKE CYLINDER CUP KIT
  1. Apply the lithium soap base glycol grease to 2 new wheel cylinder cups and 2 pistons.

  1. Install the 2 wheel cylinder cups on each piston.

  1. Install the compression spring and the 2 pistons to the wheel brake cylinder assembly.

  1. Install the 2 new cylinder dust boots to the wheel brake cylinder assembly.


3. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY

  1. C102608
    Install the wheel brake cylinder assembly with the 2 bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Using a union nut wrench, connect the brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


4. APPLY HIGH TEMPERATURE GREASE

  1. C102609E02
    Apply high temperature grease to the shoe attached surface of the backing plate.
    Text in Illustration 
    *1
    High temperature grease


5. INSTALL PARKING BRAKE SHOE STRUT SET

  1. F042695E03
    Apply the high temperature grease to the adjusting bolt.
    Text in Illustration 
    *1
    High temperature grease

  1. Install the tension spring to the shoe strut set.


6. INSTALL REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102607E02
      Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. C102606
      Connect the parking brake cable No. 3 to the front brake shoe.

    3. C102603E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

  1. for 295 mm drum:

    1. C263530E01
      Install the rear brake shoe, brake shoe strut set and shoe lever with a new C-washer.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Install a new E-ring and the automatic adjust lever.

    3. C263529
      Connect the parking brake cable No. 3 to the front brake shoe.

    4. C263525
      Install the tension spring as shown in the illustration.

    5. C263528E01
      Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  


7. INSTALL FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. Install the return spring to each brake shoe.

    2. C102604E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    3. C264855E02
      Install the brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

      NOTICE:
      Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.

    4. C102600
      Using needle-nose pliers, install the tension spring.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.
      SST
      09718-00011  

    2. Install the return spring to each brake shoe.


8. CONNECT PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, install the upper side tension spring.
      SST
      09703-30011  


9. INSTALL AUTOMATIC ADJUST LEVER

  1. for 254 mm drum:

    1. C102605
      Install the automatic adjust lever and tension spring.

      NOTICE:
      Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.


10. INSPECT REAR DRUM BRAKE

  1. Check the each part is installed properly.

    C264221E02

    C263532E01

    Text in Illustration 
    *A
    for 254 mm Drum
    *B
    for 295 mm Drum
    *C
    LH Side
    *D
    RH Side
    *a
    Front
    -
    -

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

  1. If they are not installed correctly, reinstall them as shown in the illustration.


11. INSTALL REAR AXLE BRAKE DRUM GASKET
  1. Install the new brake drum gasket to the rear axle shaft.


12. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

13. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.

    C263542E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

  1. Install the hole plug.


14. ADD BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3 or equivalent


15. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


16. INSPECT BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No.116 DOT3 or equivalent


17. INSTALL REAR WHEEL

Torque:
100 N*m{ 1020 kgf*cm , 74 ft.*lbf }


18. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.


19. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle

  1. C102142E01
    Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf) (except Super Long Wheelbase)
    12 to 18 clicks at 200 N (20 kgf, 44 lbf) (for Super Long Wheelbase)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.

← INSPECTION (from Oct 2014)INSTALLATION (Jan 2015 – Dec 2016) →