2014-2019 Hiace · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


1. REMOVE REAR WHEEL

2. DRAIN BRAKE FLUID

NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.


3. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

  1. Release the parking brake lever, and remove the brake drum.

    C318081E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

    HINT:
    If the brake drum cannot be removed easily, perform the following steps.

  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.


4. REMOVE REAR AXLE BRAKE DRUM GASKET

5. REMOVE AUTOMATIC ADJUST LEVER

  1. Remove the automatic adjust lever and the tension spring.

    C318099E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum


6. SEPARATE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C318082E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  


7. REMOVE FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. C102600
      Using a needle-nose pliers, remove the anchor side tension spring.

    2. C102601E01
      Using SST, remove the cup, shoe hold-down spring and pin.
      SST
      09718-00011  

    3. C264220E02
      Remove the parking brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

    4. Separate the brake shoe return spring, and remove the front brake shoe.

  1. for 295 mm drum:

    1. C318083E01
      Using SST, remove the cup, shoe hold-down spring and pin.
      SST
      09718-00011  

    2. Separate the brake shoe return spring, and remove the front brake shoe.


8. REMOVE REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102603E01
      Using SST, remove the cup, shoe hold-down spring and pin.
      SST
      09718-00011  

    2. C102606
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.

  1. for 295 mm drum:

    1. C318084E01
      Using SST, remove the cup, shoe hold-down spring and pin.
      SST
      09718-00011  

    2. Remove the tension spring.

    3. C318085
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.


9. REMOVE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C102607E02
      Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. Remove the adjusting bolt and tension spring from the brake shoe strut set.

  1. for 295 mm drum:

    1. C318086E01
      Remove the brake shoe strut set.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      C-washer

    2. Using a screwdriver, remove the C-washer and brake shoe lever from the brake shoe.


10. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY

  1. C102608
    Using a union nut wrench, disconnect the brake tube, use a container to catch brake fluid.

  1. Remove the 2 bolts and wheel cylinder.


11. REMOVE REAR WHEEL BRAKE CYLINDER CUP KIT
  1. Remove the 2 cylinder dust boots from the wheel cylinder.

  1. Remove the 2 pistons.

  1. Remove the 2 cylinder cups from each piston.

  1. Remove the compression spring.


12. REMOVE REAR DRUM BRAKE BLEEDER PLUG
← REMOVAL (Oct 2014 – Dec 2014)INSPECTION (from Oct 2014) →