2014-2019 Hiace · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. INSTALL BRAKE ACTUATOR ASSEMBLY

  1. C102550
    Install the brake actuator assembly to the actuator bracket with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Do not remove the hole plug until the new actuator assembly is connected because it already contains brake fluid.
    2. Insert the protrusion of the actuator bolt holder between the positioning claws of the actuator bracket No.1.
    3. Insert the positioning pin of the actuator bracket No.1 into the cushion of the actuator assembly.


2. INSTALL BRAKE ACTUATOR COVER

  1. C102549
    Install the actuator cover to the brake actuator assembly with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


3. INSTALL BRAKE TUBE

  1. C102548
    Using a union nut wrench, install the 5 brake tubes and brake way No.1 to the brake actuator assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


4. INSTALL BRAKE ACTUATOR ASSEMBLY WITH FRONT BRAKE TUBE WAY NO. 1

  1. C102547
    Install the brake actuator assembly with front brake tube way No. 1 and the brake tube to the body with the 5 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Do not bend or damage the brake tube.

  1. C102546
    Using a union nut wrench, connect the 6 brake tubes to the front brake tube way No. 1.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. C102544
    Connect the connector and lock the lock lever.

    NOTICE:
    Check that the lock lever is securely locked.


5. INSTALL FRONT MUDGUARD

  1. C102543
    Install the front mudguard with the 3 clips.


6. INSTALL FRONT BUMPER

for Standard Body:
(Click here)

for Wide Body:
(Click here)


7. INSTALL FRONT WHEEL

Torque:
100 N*m{ 1020 kgf*cm , 74 ft.*lbf }


8. ADD BRAKE FLUID

Fluid:
SAE J1703 or FMVSS No. 116 DOT3 or equivalent


9. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.


10. INSPECT BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No.116 DOT3 or equivalent

← REASSEMBLY (from Oct 2014)COMPONENTS (Oct 2014 – Dec 2014) →