REMOVAL
Removal / installation · Vehicles built Oct 2014 – Mar 2016
Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 2.
REMOVE WINDSHIELD WIPER ARM COVER
|
 |
Remove the 2 windshield wiper arm covers.
| 3.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
|
 |
Remove the nut and front wiper arm and blade assembly RH.
| 4.
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
|
 |
Remove the nut and front wiper arm and blade assembly LH.
| 5.
REMOVE COWL VENT COVER RH
|
 |
- Disengage the 2 claws and remove the cowl vent cover RH as shown in the illustration.
| 6.
REMOVE COWL VENT COVER LH
|
 |
- Disengage the 2 claws and remove the cowl vent cover LH as shown in the illustration.
| 7.
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
|
 |
- Disconnect the washer hose at position <a> shown in the illustration.
Body type narrow:
Disengage the 10 claws, and remove the 6 clips and cowl top ventilator louver sub-assembly.
Body type wide:
Disengage the 11 claws, and remove the 7 clips and cowl top ventilator louver sub-assembly.
| 8.
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
|
 |
- Disconnect the connector.
Remove the 2 bolts.
Disengage the grommet and remove the windshield wiper motor and link assembly as shown in the illustration.
| 9.
REMOVE ENGINE UNDER COVER NO.1 (w/ Under Cover and Intercooler) |
|
| 10.
DRAIN ENGINE COOLANT (w/ Intercooler) |
|
| 11.
REMOVE RADIATOR GRILLE (for Standard Body)
|
 |
- Put protective tape around the radiator grille.
Text in Illustration
*1
|
Protective Tape
|
- Remove the 4 clips and 2 screws.
Detach the 8 claws and remove the radiator grille.
| 12.
REMOVE RADIATOR GRILLE (for Wide Body)
|
 |
Put protective tape around the radiator grille.
Text in Illustration
*1
|
Protective Tape
|
- Remove the 4 clips and 2 screws.
Detach the 10 claws and remove the radiator grille.
| 13.
REMOVE NO. 2 AIR INLET DUCT (w/ Intercooler)
|
 |
- Detach the 3 clips and remove the No. 2 air inlet duct.
| 14.
REMOVE NO. 1 AIR INLET DUCT (w/ Intercooler)
|
 |
- Detach the 2 clips.
Remove the 2 bolts and No. 1 air inlet duct.
| 15.
DRAIN WINDSHIELD WASHER FLUID (w/ Intercooler) |
|
| 16.
REMOVE WINDSHIELD WASHER JAR ASSEMBLY
|
 |
- Disconnect the washer hose.
Detach the clamp.
Remove the 2 bolts and windshield washer jar.
- Disconnect the washer hose.
Detach the clamp.
Disconnect the 2 connectors.
| 17.
REMOVE RADIATOR RESERVE TANK ASSEMBLY (w/ Intercooler)
|
 |
- Disconnect the water by-pass hose.
Remove the bolt and radiator reserve tank.
- Disconnect the No. 2 water by-pass hose.
| 18.
REMOVE HOOD LOCK ASSEMBLY (w/ Intercooler)
|
 |
- Remove the 3 bolts and hood lock.
- Disconnect the hood lock control cable.
| 19.
REMOVE RADIATOR SUPPORT SUB-ASSEMBLY (w/ Intercooler)
|
 |
- Remove the hood lock control cable from the 2 clamps.
- Remove the 6 bolts, 2 screws and upper radiator support.
| 20.
REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
|
 |
- Loosen the hose clamp and disconnect the No. 2 air hose.
Loosen the hose clamp and disconnect the No. 3 air hose.
Remove the 3 bolts and intercooler.
| 21.
DISCONNECT COOLER REFRIGERANT SUCTION PIPE A |
 |
- Remove the bolt, and slide the hook connector.
Text in Illustration
*1
|
Cooler Refrigerant Suction Pipe A
|
*2
|
Hook Connector
|
*3
|
Cooler Refrigerant Liquid Pipe B
|
Disconnect the cooler refrigerant suction pipe A.
Remove the O-ring from the cooler refrigerant suction pipe A.
- NOTICE:
- Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.
| 22.
DISCONNECT COOLER REFRIGERANT LIQUID PIPE B |
 |
Disconnect the cooler refrigerant liquid pipe B.
Remove the O-ring from the cooler refrigerant liquid pipe B.
- NOTICE:
- Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.
| 23.
DISCONNECT HEATER WATER HOSE OUTLET |
 |
- Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.
Text in Illustration
*1
|
Heater Outlet Water Hose
|
*2
|
Heater Water Inlet Hose A
|
| 24.
DISCONNECT HEATER WATER HOSE INLET A |
 |
- HINT:
- Disconnection of the heater water outlet hose A is the same as for the heater water inlet hose A.
| 25.
REMOVE INSTRUMENT PANEL ASSEMBLY |
 |
(Click here)
| 26.
REMOVE STEERING COLUMN ASSEMBLY |
 |
(Click here)
| 27.
REMOVE AIR DUCT NO.1 |
 |
- Remove the clip.
Release the 2 claws and remove the air duct No.1.
| 28.
DISCONNECT PARKING BRAKE CONTROL HANDLE SUB-ASSEMBLY |
 |
- Remove the 2 bolts and disconnect the parking brake control handle sub-assembly.
| 29.
REMOVE INSTRUMENT PANEL TO FLOOR BRACE SUB-ASSEMBLY |
 |
- Remove the 5 bolts and the instrument panel to floor brace sub-assembly.
| 30.
REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
 |
Remove the clamps and connectors, and then disconnect the wire harness.


Remove the bolts, nuts and junction blocks.
Remove the 2 caps and 2 bolts.


Text in Illustration
*A
|
for Manual Transmission
|
-
|
-
|
*1
|
''Torx'' Bolt
|
*2
|
Collar
|
Remove the 2 bolts and nut. (AUTOMATIC TRANSMISSION)
Remove the 3bolts and nut. (MANUAL TRANSMISSION)
Using a "Torx" socket wrench (T40), remove the 4 "Torx" bolts.
- HINT:
- The "Torx" bolts on the passenger side can be removed with the collar for adjustment.
Using a hexagon wrench 12 mm, remove the 2 collars and instrument panel reinforcement assembly.
| 31.
REMOVE AIR CONDITIONER UNIT ASSEMBLY |
 |
Remove the 3 bolts and air conditioner unit assembly.


| 32.
REMOVE AIR DUCT NO.2 |
 |
- Release the 2 claws and remove the air duct No.2.
| 33.
REMOVE AIR CONDITIONING RADIATOR ASSEMBLY |
 |
- w/ PTC
Remove the screw and then disconnect the wire harness.
- Remove the 3 screws and air conditioning radiator assembly.