2014-2019 Hiace · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Jan 2015 – Nov 2015

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


1. INSTALL FRONT UPPER SUSPENSION ARM

  1. C102000E01
    Install the front suspension upper arm with the 3 bolts.

    Torque:
    190 N*m{ 1,940 kgf*cm , 140 ft.*lbf }


2. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

  1. C101999E01
    Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. CONNECT FRONT UPPER SUSPENSION ARM

  1. C102007E02
    Connect the front suspension upper arm to the steering knuckle with the nut.

    Torque:
    113 N*m{ 1,150 kgf*cm , 83 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    1. If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
    2. Do not damage the ball joint dust cover.


4. CONNECT FRONT SPEED SENSOR

  1. C112932E01
    Connect the front speed sensor with the 2 bolts and 2 clips.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Do not twist the sensor wire when installing.
    2. Keep the sensor tip free from foreign matter.


5. INSTALL FRONT SUSPENSION TORQUE ARM

  1. C101961E01
    Install the front suspension torque arm to the suspension upper arm with the 2 bolts.

    Torque:
    81 N*m{ 826 kgf*cm , 60 ft.*lbf }


6. TEMPORARILY TIGHTEN TORSION BAR SPRING

  1. C101964
    Check the right/left identification marks on the rear ends of the torsion bar springs.

    NOTICE:
    The end with an identification mark must be installed to the rear of the vehicle.

  1. Wrap the splines on both ends of the torsion bar spring with protective tape.

  1. Install the torsion dust cover to the torsion bar spring.

    NOTICE:
    Do not damage the lip of the dust cover when installing.

  1. C103220E02
    Remove the protective tape from the spline on both ends of the torsion bar spring and apply MP grease to them.

  1. C101959E03
    Align the matchmarks on the torsion bar spring and torque arm and engage the splines (for anchor arm side).
    Text in Illustration 
    *a
    Anchor Arm Side
    *b
    Torque Arm Side
    *c
    Matchmarks

  1. Align the matchmarks on the torsion bar spring and anchor arm and engage the splines (for torque arm side).

  1. C103229E03
    Install the following parts to the anchor arm in the following orders.
    (A) Anchor arm swivel.
    (B) Anchor arm adjusting hexagon bolt.
    (C) Anchor arm adjusting seat.
    (D) Anchor arm adjust nut.

  1. C101960E01
    Tighten the anchor arm adjust nut so that the protrusion length of the thread of the anchor arm adjusting hexagon bolt equals the length of dimension A in the table below.

    HINT:
    Australia:
    Model
    A mm (in.)
    TRH201R-RBMDKQ
    46.1 (1.81)
    TRH201R-RBTDKQ
    46.6 (1.83)
    TRH221R-MBMDKQ
    52.1 (2.05)
    TRH221R-MBTDKQ
    52.3 (2.06)
    TRH223R-LEMDKQ
    51.2 (2.02)
    TRH223R-LETDKQ
    51.7 (2.04)
    KDH201R-RBMDYQ
    45.5 (1.79)
    KDH201R-RBPDYQ
    45.8 (1.80)
    KDH201R-SSMDYQ
    45.7 (1.80)
    KDH201R-SSPDYQ
    46.1 (1.81)
    KDH221R-MBMDYQ
    51.9 (2.04)
    KDH221R-MBPDYQ
    52.0 (2.05)
    KDH223R-LEMDYQ
    56.3 (2.22)
    KDH223R-LEPDYQ
    56.8 (2.24)
    South Africa:
    Model
    A mm (in.)
    TRH201R-RBMDKN
    48.5 (1.91)
    TRH221R-MBMDKN
    53.9 (2.12)
    TRH221R-MSMDKN
    53.3 (2.10)
    TRH223R-LEMDKN
    49.0 (1.93)
    TRH213R-JDMNKN
    54.6 (2.15)
    TRH223R-LEMNKN
    52.2 (2.06)
    KDH200R-RBMDYN
    46.3 (1.82)
    KDH220R-MBMDYN
    54.1 (2.13)
    KDH220R-MSMDYN
    53.5 (2.11)
    KDH222R-LEMDYN
    51.4 (2.02)
    KDH212R-JDMNYN
    58.5 (2.30)
    KDH222R-LEMNYN
    55.6 (2.19)
    New Zealand:
    Model
    A mm (in.)
    TRH223R-LEMDKQ
    52.3 (2.06)
    KDH201R-RBMDYQ
    45.5 (1.79)
    KDH201R-RBPDYQ
    45.8 (1.80)
    KDH201R-SSPDYQ
    46.1 (1.81)
    KDH223R-LEMDYQ
    57.5 (2.26)
    KDH223R-LEPDYQ
    57.8 (2.28)
    TRH201R-SRMDK
    48.0 (1.89)
    TRH201R-SRTDK
    48.6 (1.91)
    KDH201R-SRMDY
    48.0 (1.89)
    KDH201R-SRPDY
    48.2 (1.90)
    KDH221R-MFMDY
    51.1 (2.01)
    KDH221R-MFPDY
    51.3 (2.02)
    Thailand:
    Model
    A mm (in.)
    KDH201R-RBMDYT
    47.5 (1.87)
    TRH213R-KDPNKT
    46.0 (1.81)
    KDH213R-KDPNYT
    50.3 (1.98)
    TRH223R-LEMDKT
    51.4 (2.02)
    KDH203R-RDMNYT
    48.5 (1.91)
    KDH223R-LEMDYT
    54.1 (2.13)
    KDH223R-LEPDYT
    54.1 (2.13)
    Singapore:
    Model
    A mm (in.)
    KDH221R-MBMDYQ
    54.2 (2.13)
    KDH221R-MBPDYQ
    54.4 (2.14)
    KDH223R-LEPDYQ
    56.8 (2.24)
    KDH201R-RBPDY
    47.8 (1.88)
    KDH201R-SBMDY
    48.4 (1.91)
    KDH203R-REMDY
    48.9 (1.93)
    China:
    Model
    A mm (in.)
    TRH213L-JDMNK
    54.9 (2.16)
    TRH223L-LEPNK
    54.1 (2.13)
    TRH223L-LDPNK
    57.4 (2.26)
    The Philippines:
    Model
    A mm (in.)
    KDH202L-REMDY
    51.4 (2.02)
    KDH212L-JDMNY
    59.5 (2.34)
    KDH212L-JDPNY
    59.8 (2.35)
    KDH212L-KDPNY
    50.8 (2.00)
    G.C.C. Countries (*1):
    Model
    A mm (in.)
    TRH201L-SBMDKV
    48.1 (1.89)
    TRH201L-SRMDKV
    47.1 (1.85)
    TRH221L-MBMDKV
    54.0 (2.13)
    TRH203L-REMDKV
    50.4 (1.98)
    TRH203L-REPDKV
    50.5 (1.99)
    TRH213L-JEMDKV
    55.9 (2.20)
    TRH213L-JEPDKV
    56.2 (2.21)
    TRH223L-LEMDKV
    52.0 (2.05)
    TRH223L-LEMDKV
    (Rough Road Area Spec)
    56.5 (2.22)
    TRH223L-LEPDKV
    52.0 (2.05)
    TRH223L-LEPDKV
    (Rough Road Area Spec)
    56.5 (2.22)
    TRH223L-LEMNKV
    52.5 (2.07)
    TRH223L-LEPNKV
    52.6 (2.07)
    KDH200L-SBMDYV
    47.7 (1.88)
    KDH202L-REMDYV
    51.4 (2.02)
    KDH212L-JEMDYV
    60.6 (2.39)
    KDH222L-LEMDYV
    53.9 (2.12)
    KDH222L-LEMDYV
    (Rough Road Area Spec)
    58.6 (2.31)
    KDH222L-LEMNYV
    54.2 (2.13)
    (*1):
    Saudi Arabia, Sultanate of Oman, Bahrain, United Arab Emirates, Qatar and Kuwait
    Russia:
    Model
    A mm (in.)
    TRH223L-LEMNKX
    52.0 (2.05)
    KDH223L-LEMNYX
    59.3 (2.33)
    Hong Kong:
    Model
    A mm (in.)
    TRH200R-SSTDK
    48.3 (1.90)
    KDH201R-SSMDY
    49.0 (1.93)
    KDH201R-SSPDY
    49.4 (1.94)
    KDH201R-SSPNY
    48.4 (1.91)
    Mexico:
    Model
    A mm (in.)
    TRH221L-MBMDK
    54.1 (2.13)
    TRH221L-LFMDK
    53.9 (2.12)
    TRH223L-LEMNK
    54.7 (2.15)
    Peru:
    Model
    A mm (in.)
    KDH200L-SBMDY
    47.7 (1.88)
    LH200L-RBMDE
    45.8 (1.80)
    KDH202L-RDMDY
    51.4 (2.02)
    KDH212L-JDMNY
    59.6 (2.35)
    KDH222L-LEMDY
    58.8 (2.31)
    LH202L-REMDE
    49.9 (1.96)
    LH222L-LEMDE
    58.3 (2.30)
    Chile:
    Model
    A mm (in.)
    KDH201L-SBMDY
    49.0 (1.93)
    KDH203L-RDMDY
    52.3 (2.06)
    KDH213L-JDMNY
    60.8 (2.39)
    Ecuador:
    Model
    A mm (in.)
    LH200L-RBMDE
    45.6 (1.80)
    LH202L-REMDE
    49.9 (1.96)
    LH212L-JEMDE
    59.0 (2.32)
    LH222L-LEMDE
    58.3 (2.30)
    Tunisia:
    Model
    A mm (in.)
    KDH202L-RDMDY
    48.0 (1.89)
    Malaysia:
    Model
    A mm (in.)
    KDH200R-RBMDYE
    45.1 (1.78)
    TRH203R-EDMDKE
    50.4 (1.98)
    KDH202R-EDMDYE
    49.9 (1.96)
    Vietnam:
    Model
    A mm (in.)
    TRH223L-LEMDK
    56.3 (2.22)
    KDH222L-LEMDY
    58.8 (2.31)
    Morocco:
    Model
    A mm (in.)
    KDH201L-RBMDY
    48.0 (1.89)
    KDH223L-LEMDY
    57.3 (2.26)
    India:
    Model
    A mm (in.)
    KDH223R-LDPNY
    61.9 (2.44)
    Others:
    Model
    A mm (in.)
    TRH201L-SBMDK
    48.3 (1.90)
    TRH221L-MBMDK
    54.1 (2.13)
    KDH200R-RBMDY
    47.7 (1.88)
    KDH200R-SBMDY
    47.8 (1.88)
    KDH200L-RBMDY
    47.6 (1.87)
    KDH200L-SBMDY
    47.5 (1.87)
    KDH220L-MBMDY
    54.1 (2.13)
    LH200R-RBMDE
    46.2 (1.82)
    LH200R-SBMDE
    46.4 (1.83)
    LH200L-RBMDE
    46.2 (1.82)
    TRH203R-REMDK
    50.1 (1.97)
    TRH203L-REMDK
    50.6 (1.99)
    TRH213R-JEMDK
    56.0 (2.20)
    TRH213L-JEMDK
    56.0 (2.20)
    TRH223R-LEMDK
    51.7 (2.04)
    TRH223R-LEMDK
    (Rough Road Area Spec)
    56.3 (2.22)
    TRH223L-LEMDK
    51.7 (2.04)
    TRH223L-LEMDK
    (Rough Road Area Spec)
    56.3 (2.22)
    TRH223L-LEMNK
    52.3 (2.06)
    TRH223L-LEMNK
    (Rough Road Area Spec)
    56.9 (2.24)
    KDH202R-REMDY
    52.0 (2.05)
    KDH202L-REMDY
    52.2 (2.06)
    KDH202L-RDMDY
    51.9 (2.04)
    KDH212R-JEMDY
    60.6 (2.39)
    KDH212L-JEMDY
    60.8 (2.39)
    KDH222R-LEMDY
    53.9 (2.12)
    KDH222R-LEMDY
    (Rough Road Area Spec)
    58.6 (2.31)
    KDH222R-LEPNY
    54.0 (2.13)
    KDH222R-LEPNY
    (Rough Road Area Spec)
    58.7 (2.31)
    KDH222L-LEMDY
    53.9 (2.12)
    KDH222L-LEMDY
    (Rough Road Area Spec)
    58.6 (2.31)
    KDH222L-LEPNY
    54.0 (2.13)
    KDH222L-LEPNY
    (Rough Road Area Spec)
    58.7 (2.31)
    LH202R-REMDE
    50.2 (1.98)
    LH202L-REMDE
    50.4 (1.98)
    LH202L-RDMDE
    50.4 (1.98)
    LH212R-JEMDE
    58.8 (2.31)
    LH212L-JEMDE
    59.0 (2.32)
    LH222R-LEMDE
    53.8 (2.12)
    LH222R-LEMDE
    (Rough Road Area Spec)
    58.4 (2.30)
    LH222L-LEMDE
    53.8 (2.12)
    LH222L-LEMDE
    (Rough Road Area Spec)
    58.4 (2.30)


7. INSTALL FENDER APRON MUDGUARD SEAL

  1. C101965E02
    Install the fender apron mudguard seal with the 4 clips.


8. INSTALL FRONT WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


9. STABILIZE SUSPENSION

10. FULLY TIGHTEN TORSION BAR SPRING

  1. C103219E03
    Hold the anchor arm adjust nut and fully tighten the anchor lock nut.
    Text in Illustration 
    *1
    Adjust Nut
    *2
    Lock Nut

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }


11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)
← INSTALLATION (Oct 2014 – Dec 2014)INSTALLATION (Dec 2015 – Mar 2016) →