INSTALLATION
Removal / installation · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| 1. INSTALL FRONT UPPER SUSPENSION ARM |
Install the front suspension upper arm with the 3 bolts.

- Torque:
- 190 N*m{ 1,940 kgf*cm , 140 ft.*lbf }
| 2. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY |
Install the vane pump oil reservoir assembly with the 2 bolts.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 3. CONNECT FRONT UPPER SUSPENSION ARM |
Connect the front suspension upper arm to the steering knuckle with the nut.

- Torque:
- 113 N*m{ 1,150 kgf*cm , 83 ft.*lbf }
Install a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
- Do not damage the ball joint dust cover.
- If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
| 4. CONNECT FRONT SPEED SENSOR |
Connect the front speed sensor with the 2 bolts and 2 clips.

- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
- NOTICE:
- Do not twist the sensor wire when installing.
- Keep the sensor tip free from foreign matter.
- Do not twist the sensor wire when installing.
| 5. INSTALL FRONT SUSPENSION TORQUE ARM |
Install the front suspension torque arm to the suspension upper arm with the 2 bolts.

- Torque:
- 81 N*m{ 826 kgf*cm , 60 ft.*lbf }
| 6. TEMPORARILY TIGHTEN TORSION BAR SPRING |
Check the right/left identification marks on the rear ends of the torsion bar springs.

- NOTICE:
- The end with an identification mark must be installed to the rear of the vehicle.
Wrap the splines on both ends of the torsion bar spring with protective tape.
Install the torsion dust cover to the torsion bar spring.
- NOTICE:
- Do not damage the lip of the dust cover when installing.
Remove the protective tape from the spline on both ends of the torsion bar spring and apply MP grease to them.

Align the matchmarks on the torsion bar spring and torque arm and engage the splines (for anchor arm side).

Text in Illustration *a
Anchor Arm Side
*b
Torque Arm Side
*c
Matchmarks
Align the matchmarks on the torsion bar spring and anchor arm and engage the splines (for torque arm side).
Install the following parts to the anchor arm in the following orders.

(A) Anchor arm swivel.
(B) Anchor arm adjusting hexagon bolt.
(C) Anchor arm adjusting seat.
(D) Anchor arm adjust nut.
Tighten the anchor arm adjust nut so that the protrusion length of the thread of the anchor arm adjusting hexagon bolt equals the length of dimension A in the table below.

- HINT:
- Australia:
Model
A mm (in.)
TRH201R-RBMDKQ
46.1 (1.81)
TRH201R-RBTDKQ
46.6 (1.83)
TRH221R-MBMDKQ
52.1 (2.05)
TRH221R-MBTDKQ
52.3 (2.06)
TRH223R-LETDKQ
51.7 (2.04)
KDH201R-RBMDYQ
45.8 (1.80)
KDH201R-RBPDYQ
46.3 (1.82)
KDH201R-SSMDYQ
46.1 (1.81)
KDH201R-SSPDYQ
46.4 (1.83)
KDH221R-MBMDYQ
52.2 (2.06)
KDH221R-MBPDYQ
52.3 (2.06)
KDH223R-LEMDYQ
56.8 (2.24)
KDH223R-LEPDYQ
57.0 (2.24)
- South Africa:
Model
A mm (in.)
TRH201R-RBMDKN
48.5 (1.91)
TRH221R-MBMDKN
53.9 (2.12)
TRH221R-MSMDKN
53.3 (2.10)
TRH213R-JDMNKN
54.6 (2.15)
TRH223R-LEMDKN
49.0 (1.93)
TRH223R-LEMNKN
52.2 (2.06)
KDH200R-RBMDYN
46.3 (1.82)
KDH220R-MBMDYN
54.1 (2.13)
KDH220R-MSMDYN
53.5 (2.11)
KDH212R-JDMNYN
58.5 (2.30)
KDH222R-LEMDYN
51.4 (2.02)
KDH222R-LEMNYN
55.6 (2.19)
- New Zealand:
Model
A mm (in.)
KDH201R-RBPDYQ
46.3 (1.82)
KDH201R-SSPDYQ
46.4 (1.83)
KDH223R-LEMDYQ
57.9 (2.28)
KDH223R-LEPDYQ
58.3 (2.30)
TRH201R-SRMDK
48.0 (1.89)
TRH201R-SRTDK
48.6 (1.91)
KDH201R-SRMDY
48.4 (1.91)
KDH201R-SRPDY
48.5 (1.91)
KDH221R-MFMDY
51.5 (2.03)
KDH221R-MFPDY
51.5 (2.03)
TRH201R-RBMDKQ
46.1 (1.81)
- Thailand:
Model
A mm (in.)
KDH201R-RBMDYT
47.5 (1.87)
TRH213R-KDPNKT
46.0 (1.81)
KDH213R-KDPNYT
50.3 (1.98)
TRH223R-LEMDKT
51.4 (2.02)
KDH203R-RDMNYT
48.5 (1.91)
KDH223R-LEMDYT
54.1 (2.13)
KDH223R-LEPDYT
54.1 (2.13)
- Fiji:
Model
A mm (in.)
KDH201R-RBMDYT
47.5 (1.87)
KDH223R-LEMDYT
58.8 (2.31)
- Singapore:
Model
A mm (in.)
KDH221R-MBMDYQ
54.2 (2.13)
KDH221R-MBPDYQ
54.4 (2.14)
KDH223R-LEPDYQ
56.8 (2.24)
KDH201R-RBPDY
47.8 (1.88)
KDH201R-SBMDY
48.4 (1.91)
KDH203R-REMDY
48.9 (1.93)
- China:
Model
A mm (in.)
TRH223L-LEPNK
54.1 (2.13)
- The Philippines:
Model
A mm (in.)
KDH203L-REMDY
52.3 (2.06)
KDH213L-JDMNY
63.5 (2.50)
KDH213L-JDPNY
63.7 (2.51)
KDH213L-KDPNY
52.4 (2.06)
KDH223L-LEPNY
56.3 (2.22)
- G.C.C. Countries (*1):
Model
A mm (in.)
TRH201L-SBMDKV
48.1 (1.89)
TRH201L-SRMDKV
47.1 (1.85)
TRH221L-MBMDKV
54.0 (2.13)
TRH203L-REMDKV
50.4 (1.98)
TRH203L-REPDKV
50.5 (1.99)
TRH223L-LEMDKV
52.0 (2.05)
TRH223L-LEMDKV
(Rough Road Area Spec)
56.5 (2.22)
TRH223L-LEPDKV
52.0 (2.05)
TRH223L-LEPDKV
(Rough Road Area Spec)
56.5 (2.22)
TRH223L-LEMNKV
52.5 (2.07)
TRH223L-LEMNKV
(Rough Road Area Spec)
57.0 (2.24)
TRH223L-LEPNKV
52.6 (2.07)
TRH223L-LEPNKV
(Rough Road Area Spec)
57.2 (2.25)
KDH200L-SBMDYV
47.7 (1.88)
KDH202L-REMDYV
51.4 (2.02)
KDH212L-JEMDYV
60.6 (2.39)
KDH222L-LEMDYV
53.9 (2.12)
KDH222L-LEMDYV
(Rough Road Area Spec)
58.6 (2.31)
KDH222L-LEMNYV
54.2 (2.13)
KDH222L-LEMNYV
(Rough Road Area Spec)
59.0 (2.32)
- (*1):
- Saudi Arabia, Sultanate of Oman, Bahrain, United Arab Emirates, Qatar and Kuwait
- Azerbaijan:
Model
A mm (in.)
KDH201L-RBMDY
48.9 (1.93)
KDH223L-LEMNYX
59.0 (2.32)
- Hong Kong:
Model
A mm (in.)
TRH200R-SSTDK
48.3 (1.90)
GDH201R-SSTDY
50.1 (1.97)
GDH201R-SSTNY
49.3 (1.94)
- Mexico:
Model
A mm (in.)
TRH221L-MBMDK
54.1 (2.13)
TRH221L-LFMDK
53.9 (2.12)
TRH223L-LEMNK
54.7 (2.15)
- Peru:
Model
A mm (in.)
KDH201L-SBMDY
48.7 (1.92)
KDH203L-RDMDY
52.4 (2.06)
KDH213L-JDMNY
60.8 (2.39)
KDH223L-LEMDY
59.1 (2.33)
- Chile:
Model
A mm (in.)
KDH201L-SBMDY
49.0 (1.93)
KDH203L-RDMDY
52.3 (2.06)
KDH213L-JDMNY
60.8 (2.39)
- Caucasus:
Model
A mm (in.)
KDH220L-MBMDY
53.7 (2.11)
KDH222L-LEMNYV
59.3 (2.33)
- Tunisia:
Model
A mm (in.)
KDH202L-RDMDY
48.0 (1.89)
- Malaysia:
Model
A mm (in.)
KDH200R-RBMDYE
45.1 (1.78)
- Vietnam:
Model
A mm (in.)
TRH223L-LEMDK
56.3 (2.22)
KDH223L-LEMDY
59.0 (2.32)
- Morocco:
Model
A mm (in.)
KDH201L-RBMDY
48.0 (1.89)
KDH223L-LEMDY
57.3 (2.26)
- General Export:
Model
A mm (in.)
TRH201L-SBMDK
48.3 (1.90)
TRH221L-MBMDK
54.1 (2.13)
KDH200R-RBMDY
47.7 (1.88)
KDH200R-SBMDY
47.8 (1.88)
KDH200L-RBMDY
47.6 (1.87)
KDH200L-SBMDY
47.5 (1.87)
KDH220L-MBMDY
54.1 (2.13)
LH200R-RBMDE
46.2 (1.82)
LH200R-SBMDE
46.4 (1.83)
LH200L-RBMDE
46.2 (1.82)
TRH203R-REMDK
50.1 (1.97)
TRH203L-REMDK
50.6 (1.99)
TRH213R-JEMDK
56.0 (2.20)
TRH213L-JEMDK
56.0 (2.20)
TRH223L-LEMDK
51.7 (2.04)
TRH223L-LEMDK
(Rough Road Area Spec)
56.3 (2.22)
TRH223R-LEMDK
51.7 (2.04)
TRH223R-LEMDK
(Rough Road Area Spec)
56.3 (2.22)
TRH223L-LEMNK
52.3 (2.06)
TRH223L-LEMNK
(Rough Road Area Spec)
56.9 (2.24)
KDH202R-REMDY
52.0 (2.05)
KDH202L-REMDY
52.2 (2.06)
KDH202L-RDMDY
51.9 (2.04)
KDH212R-JEMDY
60.6 (2.39)
KDH212L-JEMDY
60.8 (2.39)
KDH222R-LEMDY
53.9 (2.12)
KDH222R-LEMDY
(Rough Road Area Spec)
58.6 (2.31)
KDH222R-LEPNY
54.0 (2.13)
KDH222R-LEPNY
(Rough Road Area Spec)
58.7 (2.31)
KDH222L-LEMDY
53.9 (2.12)
KDH222L-LEMDY
(Rough Road Area Spec)
58.6 (2.31)
KDH222L-LEPNY
54.0 (2.13)
KDH222L-LEPNY
(Rough Road Area Spec)
58.7 (2.31)
LH202R-REMDE
50.2 (1.98)
LH202L-REMDE
50.4 (1.98)
LH202L-RDMDE
50.4 (1.98)
LH212R-JEMDE
58.8 (2.31)
LH212L-JEMDE
59.0 (2.32)
LH222R-LEMDE
53.8 (2.12)
LH222R-LEMDE
(Rough Road Area Spec)
58.4 (2.30)
LH222L-LEMDE
53.8 (2.12)
LH222L-LEMDE
(Rough Road Area Spec)
58.4 (2.30)
| 7. INSTALL FENDER APRON MUDGUARD SEAL |
Install the fender apron mudguard seal with the 4 clips.

| 8. INSTALL FRONT WHEEL |
- Torque:
- 100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }
| 9. STABILIZE SUSPENSION |
| 10. FULLY TIGHTEN TORSION BAR SPRING |
Hold the anchor arm adjust nut and fully tighten the anchor lock nut.

Text in Illustration *1
Adjust Nut
*2
Lock Nut
- Torque:
- 78 N*m{ 795 kgf*cm , 58 ft.*lbf }
| 11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
