2014-2019 Hiace · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. CLEAN BACK DOOR GLASS

  1. B073128E02
    Using a scraper, remove the spacers, moulding and adhesive from the back door glass.

  1. Clean the outer edge of the back door glass with non-residue solvent.

    NOTICE:
    1. Do not touch the back door glass surface after cleaning it.
    2. Even if using new back door glass, clean the back door glass with non-residue solvent.


2. CLEAN VEHICLE BODY

  1. B073084E13
    Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.

      Text in Illustration 
      *1
      Adhesive
      *2
      Vehicle Body


3. INSTALL BACK WINDOW GLASS CLIP LH

  1. B102894E05
    Apply Primer G to the glass where the clip will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install new clip onto the back door glass as shown in the illustration.

    Text in Illustration 
    *1
    Back Window Glass Clip LH
    *a
    Backside


4. INSTALL BACK WINDOW GLASS CLIP RH

  1. B102894E06
    Apply Primer G to the glass where the clip will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install a new clip onto the back door glass as shown in the illustration.

    Text in Illustration 
    *1
    Back Window Glass Clip RH
    *a
    Backside


5. INSTALL BACK DOOR GLASS NO. 1 SPACER

  1. B102894E07
    Apply Primer G to the glass where the spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the back door glass as shown in the illustration.

    Text in Illustration 
    *1
    Back Window Glass No. 1 Spacer
    *a
    Backside


6. INSTALL BACK WINDOW GLASS NO. 2 SPACER

  1. B102894E08
    Apply Primer G to the glass where the spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the back door glass as shown in the illustration.

    Text in Illustration 
    *1
    Back Window Glass No. 2 Spacer LH
    *a
    Backside


7. INSTALL BACK DOOR GLASS

  1. B114789E02
    Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
    Text in Illustration 
    *A
    CORRECT
    *B
    INCORRECT
    *1
    Primer M
    *2
    Adhesive

    NOTICE:

    1. B101853E02
      Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

    Text in Illustration 
    *1
    Primer M

  1. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

    B114787E04

    Text in Illustration 
    *1
    Adhesive
    *2
    Adhesive Center Line
    *a
    Backside
    -
    -

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Apply adhesive to the back door glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent

  1. B115241E02
    Cut off the tip of cartridge nozzle as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    12.0 mm (0.472 in.)
    b
    8.0 mm (0.315 in.)

    HINT:
    After cutting off the tip, use all adhesive within the time written in the table below.

    Usage Time Frame:
    Temperature
    Usage Time Frame
    35°C (95°F)
    15 minutes
    20°C (68°F)
    1 hour 40 minutes
    5°C (41°F)
    8 hours

  1. Load the sealer gun with the cartridge.

  1. Apply adhesive to the back door glass as shown in the illustration.

    B115252E02

    Text in Illustration 
    *a
    Backside
    -
    -
    Specification 
    Area
    Measurement
    a
    12.0 mm (0.472 in.)
    b
    8.0 mm (0.315 in.)
    c
    13.0 mm (0.511 in.)

  1. Install the back door glass to the vehicle body.

    1. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and back door glass have a small gap between them.

    2. Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


8. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.


9. INSTALL EMERGENCY HAMMER CAUTION PLATE (w/ Emergency Hammer Caution Plate)

  1. Ifor Type A:

    1. Install the emergency hammer caution plate as shown in the illustration.

      B451048E01

      Text in Illustration 
      *1
      Ceramic Line
      *2
      Edge of Dam
      *a
      Backside
      -
      -

  1. Ifor Type B:

    1. Install the emergency hammer caution plate as shown in the illustration.

      B451051E01

      Text in Illustration 
      *1
      Ceramic Line
      *2
      Ceramic Notch
      *a
      Backside
      -
      -

  1. Remove the peeling paper.


10. INSTALL REAR WIPER MOTOR ASSEMBLY

  1. E104706E01
    Install the grommet as shown in the illustration.

  1. E103138E01
    Install the rear wiper motor with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the clamp and connect the connector.


11. INSTALL BACK DOOR TRIM BOARD ASSEMBLY UPPER
  1. w/o Rear Wiper:
    (Click here)

  1. w/ Rear Wiper:
    (Click here)

  1. for Wide Body:
    (Click here)


12. INSTALL REAR WIPER LINK PIVOT WASHER NO.1

  1. E103141E02
    Install the rear No.1 wiper link pivot washer from the outside of the vehicle with the installation mark at the top.

  1. E103140
    Using the socket wrench (27 mm), install the lock nut.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not damage the glass.


13. INSTALL REAR WIPER SHAFT COVER

14. INSTALL REAR WIPER ARM

  1. B108016E03
    Operate the wiper, and stop the rear wiper motor at the automatic stop position.

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).

  1. E103534E01
    Install the rear wiper arm and blade assembly with the nut at the position as shown in the illustration.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.

  1. Operate the rear wiper while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.

← INSTALLATION (Oct 2014 – Dec 2016)COMPONENTS (from Oct 2014) →