Home › BODY › WINDSHIELD / WINDOWGLASS › BACK DOOR GLASS
INSTALLATION
Removal / installation · Vehicles built Oct 2014 – Dec 2016
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
1.
CLEAN BACK DOOR GLASS
Using a scraper, remove the spacers, moulding and adhesive from the back door glass.
Clean the outer edge of the back door glass with non-residue solvent.
NOTICE:
Do not touch the back door glass surface after cleaning it.
Even if using new back door glass, clean the back door glass with non-residue solvent.
2.
CLEAN VEHICLE BODY
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
HINT:
Leave as much adhesive on the vehicle body as possible.
NOTICE:
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
HINT:
Even if all the adhesive has been removed, clean the vehicle body.
Text in Illustration
*1
Adhesive
*2
Vehicle Body
3.
INSTALL BACK WINDOW GLASS CLIP LH
Apply Primer G to the glass where the clip will be installed.
HINT:
If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
NOTICE:
Allow the Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
Install new clip onto the back door glass as shown in the illustration.
Text in Illustration
*1
Back Window Glass Clip LH
*a
Backside
4.
INSTALL BACK WINDOW GLASS CLIP RH
Apply Primer G to the glass where the clip will be installed.
HINT:
If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
NOTICE:
Allow the Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
Install a new clip onto the back door glass as shown in the illustration.
Text in Illustration
*1
Back Window Glass Clip RH
*a
Backside
5.
INSTALL BACK DOOR GLASS NO. 1 SPACER
Apply Primer G to the glass where the spacers will be installed.
HINT:
If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
NOTICE:
Allow the Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
Install 2 new spacers onto the back door glass as shown in the illustration.
Text in Illustration
*1
Back Window Glass No. 1 Spacer
*a
Backside
6.
INSTALL BACK WINDOW GLASS NO. 2 SPACER
Apply Primer G to the glass where the spacers will be installed.
HINT:
If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
NOTICE:
Allow the Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
Install 2 new spacers onto the back door glass as shown in the illustration.
Text in Illustration
*1
Back Window Glass No. 2 Spacer LH
*a
Backside
7.
INSTALL BACK DOOR GLASS
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Text in Illustration
*A
CORRECT
*B
INCORRECT
*1
Primer M
*2
Adhesive
NOTICE:
Allow the Primer M to dry for 3 minutes or more.
Do not apply Primer M to the adhesive.
Throw away any leftover Primer M.
Do not apply too much Primer M.
Text in Illustration
*1
Primer M
Using a brush or sponge, apply Primer G to the contact surface of the back door glass.
Text in Illustration
*1
Adhesive
*2
Adhesive Center Line
*a
Backside
-
-
HINT:
If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
NOTICE:
Allow the Primer G to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much Primer G.
Apply adhesive to the back door glass.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of cartridge nozzle as shown in the illustration.
Specification:
Area
Measurement
a
12.0 mm (0.472 in.)
b
8.0 mm (0.315 in.)
HINT:
After cutting off the tip, use all adhesive within the time written in the table below.
Usage Time Frame:
Temperature
Usage Time Frame
35°C (95°F)
15 minutes
20°C (68°F)
1 hour 40 minutes
5°C (41°F)
8 hours
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass as shown in the illustration.
Text in Illustration
*a
Backside
-
-
Specification
Area
Measurement
a
12.0 mm (0.472 in.)
b
8.0 mm (0.315 in.)
c
13.0 mm (0.511 in.)
Install the back door glass to the vehicle body.
Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.
NOTICE:
Check that the spacers are attached to the vehicle body correctly.
Check that the vehicle body and back door glass have a small gap between them.
Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.
NOTICE:
Do not drive the vehicle for the amount of time written in the table below.
Minimum Time:
Temperature
Minimum Time Prior to Driving Vehicle
35°C (95°F)
1 hour 30 minutes
20°C (68°F)
5 hours
5°C (41°F)
24 hours
8.
CHECK FOR LEAKS AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
9.
INSTALL EMERGENCY HAMMER CAUTION PLATE (w/ Emergency Hammer Caution Plate)
Install the emergency hammer caution plate as shown in the illustration.
Text in Illustration
*1
Ceramic Line
-
-
*a
Backside
*b
R End
Specification:
Area
Measurement
a
23 mm (0.9 in.)
Remove the peeling paper.
10.
INSTALL REAR WIPER MOTOR ASSEMBLY
Install the grommet as shown in the illustration.
Install the rear wiper motor with the 3 bolts.
Torque:
5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
Install the clamp and connect the connector.
11.
INSTALL BACK DOOR TRIM BOARD ASSEMBLY UPPER
w/o Rear Wiper: (Click here )
w/ Rear Wiper: (Click here )
for Wide Body: (Click here )
12.
INSTALL REAR WIPER LINK PIVOT WASHER NO.1
Install the rear No.1 wiper link pivot washer from the outside of the vehicle with the installation mark at the top.
Using the socket wrench (27 mm), install the lock nut.
Torque:
12 N*m{
120 kgf*cm
, 9 ft.*lbf
}
NOTICE:
Do not damage the glass.
13.
INSTALL REAR WIPER SHAFT COVER
14.
INSTALL REAR WIPER ARM
Operate the wiper, and stop the rear wiper motor at the automatic stop position.
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush (when reinstalling).
Install the rear wiper arm and blade assembly with the nut at the position as shown in the illustration.
Torque:
9.8 N*m{
100 kgf*cm
, 87 in.*lbf
}
HINT:
Hold the arm hinge by hand to fasten the nut.
Operate the rear wiper while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.