2014-2019 Hiace · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014


DATA LIST

HINT:
By reading the Data List displayed on the intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    HINT:
    If no idling conditions are specified, the transmission gear selector lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    600 to 700 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 26%: Idling
    2. 12 to 27%: Running without load (2500 rpm)
    -
    MAF
    Air flow rate from MAF meter/
    Min.: 0 gm/s, Max.: 655.35 gm/s
    2.0 to 4.5 gm/s: Idling
    1. If value approximately 0.0 gm/s:
      1. Mass air flow meter power source circuit open
    2. VG circuit open or short if value 160.0 gm/s or more:
      1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure
    (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    75 to 100°C (167 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data
    Radiator Coolant Temp
    Engine coolant (radiator) temperature/
    Min.: -40°C, Max.: 140°C
    75 to 100°C (167 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.5 V
    11 to 14 V: Idling
    -
    Accel Sens. No.1 Volt %
    Absolute Accelerator Pedal Position (APP) No.1/
    Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal released
    52 to 90%: Accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute APP No.2/
    Min.: 0%, Max.: 100%
    24 to 40%: Accelerator pedal released
    68 to 95%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    APP sensor No.1 voltage/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.2
    APP sensor No.2 voltage/
    Min.: 0 V, Max.: 4.9 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 4.7 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No.1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No.1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No.2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Throttle Sensor Volt %
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    -
    Throttle Sensor #2 Volt %
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Throttle fully closed
    2. 92 to 100%: Throttle fully open
    Calculated value based on VTA2
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    10 to 18%: Idling
    Calculated value based on VTA1
    Throttle Position No.1
    Throttle position No.1/
    Min.: 0 V, Max.: 4.9 V
    1. 0.5 to 1.1 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully open
    -
    Throttle Position No.2
    Throttle position No.2/
    Min.: 0 V, Max.: 4.9 V
    1. 2.1 to 3.1 V: Throttle fully closed
    2. 4.6 to 4.9 V: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.9 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No.1/
    Min.: 0 V, Max.: 4.9 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No.2/
    Min.: 0 V, Max.: 4.9 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No.1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle actuator control permitted/
    ON or OFF
    ON: Idling
    Read value with ignition switch ON
    (Do not start engine)
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    -
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    -
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 100%
    0 to 40%: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close)/
    Min.: 0%, Max.: 100%
    0 to 40%: Idling
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.9 V
    0.4 to 0.8 V
    -
    ETCS Actuator Power
    Whether or not electronic throttle control system power input/
    ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage/
    Min.: 0, Max.: 19.9
    10 to 15 V: Idling
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data
    Fail Safe Drive
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Injector (Port)
    Injection period of No.1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    1.8 to 3.8 ms: Idling
    -
    Injection Volum (Cylinder1)
    Injection volume/
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    Active Test support data
    Evap Purge Flow*
    Purge flow/
    Min.: 0%, Max.: 102.3%
    0 to 100%: Idling
    -
    Purge Density Learn Value*
    Learning value of purge density/
    Min.: -50, Max.: 349.99
    -40 to 0%: Idling
    Service data
    EVAP Purge VSV*
    VSV status for EVAP control/
    ON or OFF
    -
    -
    Target Air-Fuel Ratio*
    Air-fuel ratio/
    Min.: 0, Max.: 1.998
    0.8 to 1.2: Idling
    -
    O2S B1S1*
    Heated oxygen sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 1.27 V
    0 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing Inj Vol or A/F Control function of Active Test enables technician to check voltage output of sensor
    Short FT #1*
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1*
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    Overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
    Fuel System Status #1*
    Fuel system status (Bank 1)/
    OL or CL or OLDrive or OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    3. OLDrive: Open loop due to driving conditions (fuel enrichment)
    4. OLFault: Open loop due to detected system fault
    5. CLFault: Closed loop but heated oxygen sensor, which used for fuel control, malfunction
    Fuel System Status #2*
    Fuel system status (Bank 2)/
    OL or CL or OLDrive or OLFault or CLFault
    Unused
    O2FT B1S1*
    Short-term fuel trim of associated with bank 1 sensor 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%: Idling
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg, Max.: 63.5 deg
    BTDC 4 to 17 deg: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -64 deg(CA), Max.: 1983.9 deg(CA)
    -19 to 0 deg(CA):
    Driving, 70 km/h (44 mph)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -64 deg(CA), Max.: 1983.9 deg(CA)
    0 to 19 deg(CA):
    Driving, 70 km/h (44 mph)
    Service data
    VVT Control Status #1
    VVT control status/
    ON or OFF
    -
    -
    VVT Aim Angle #1
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle #1
    VVT change angle/
    Min.: 0 DegFR, Max.: 60 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #1
    VVT OCV operation duty/
    Min.: 0%, Max.: 100%
    0%: Idling
    Requested duty value for intrusive operation
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal
    Power steering signal/
    ON or OFF
    ON: Power steering operation
    -
    Power Steer. Sig. Record
    Power steering signal/
    ON or OFF
    ON: When steering wheel first turned after ignition switch turned to ON
    This signal status usually ON until ignition switch turned to OFF
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C signal/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Electrical Load Signal
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger turned ON
    -
    Check Mode
    Check mode/
    ON or OFF
    Check mode ON
    Click here
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    # Codes(Include History)
    # Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs erased
    -
    Warm up Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    OBD Requirements
    OBD requirements
    Not OBD compliant
    -
    Number of Emission DTC
    Number of emission DTCs
    -
    -
    TC and TE1
    TC and TE terminals of DLC3/
    ON or OFF
    -
    Active Test support data
    Electric Fan Motor
    Electric fan motor status/
    ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
    FC TAU
    Fuel cut TAU (Fuel cut during very light load)/
    ON or OFF
    ON: Fuel cut operation
    Fuel cut initiated under very light load to prevent in complete combustion
    Model Code
    Model code
    -
    Identifying model code:
    TRH2###
    Engine Type
    Engine type
    -
    Identifying engine type:
    2TR
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying cylinder number:
    4
    Transmission Type
    Transmission type
    -
    Identifying transmission type:
    MT
    Destination
    Destination
    -
    Identifying destination:
    W
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying model year:
    20##
    *: Except leaded gasoline specification vehicle


ACTIVE TEST

HINT:
Performing an Active Test using the intelligent tester enables components including the relay, VSV, and actuator to be operated without removing any parts. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time.
Data List is displayed during an Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. Perform the Active Test by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All injectors tested at the same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed in 0.1 or 0.2% graduations within control range
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5% / 0% / 12.5%
    1. Perform test at less than 3000 rpm
    2. A/F Control enables to check and graph heated oxygen sensor voltage outputs
    3. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / User Data / O2S B1S1
    Activate the VSV for Evap Control*
    Activate EVAP VSV control
    ON/OFF
    The valve is opened with a 30% duty ratio.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Shift lever in neutral
    Connect the TC and TE1
    Turn ON and OFF TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    Activate cooling fan
    ON/OFF
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Shift lever in neutral
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    ON: throttle valve opens slowly
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    ON: throttle valve opens fast
    Control the VVT Linear (Bank 1)
    Activate OCV
    Min.: -128%, Max.: 127%
    1. Test possible during vehicle stopping and engine idling
    2. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn ON and OFF OCV
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON
    2. Normal engine running or idling when OCV OFF
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the Cylinder#1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling
    Control the Cylinder#2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Control the Cylinder#3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Control the Cylinder#4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    *: Except leaded gasoline specification vehicle

← FAIL-SAFE CHART (from Oct 2014)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →