P1115 Coolant Temperature Sensor Circuit for Coolant Heat Storage System / Intake Air Temperature Circuit
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 from Jan 2015
DESCRIPTION
The intake air temperature sensor senses the intake air temperature. A thermistor built in this sensor changes the resistance value according to the intake air temperature as shown in the illustration. This resistance value of intake air temperature sensor is one of the factors used to decide the fuel injection volume.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1115 |
Open or short in intake air temperature sensor circuit for 0.5 seconds or more. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING GTS (INTAKE AIR TEMPERATURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
- Result:
Display
Proceed
-40°C (-40°F)
A
140°C (284°F) or more
B
The same as actual engine coolant temperature
C
- HINT:
- If there is an open circuit, the GTS indicates -40°C (- 40°F).
- If there is a short circuit, the GTS indicates 140°C (284°F) or more.
- If there is an open circuit, the GTS indicates -40°C (- 40°F).
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN) |
Disconnect the intake air temperature sensor connector.

Connect terminals 1 and 2 of the intake air temperature sensor harness side connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
- Temperature:
- 140°C (284°F) or more
Text in Illustration *1
Intake Air Temperature Sensor
*2
ECM
*a
Front view of wire harness connector
(to Intake Air Temperature Sensor)
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR) |
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A2-2 - D100-71 (THA)
Always
Below 1 Ω
A2-1 - D100-94 (ETHA)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Disconnect the intake air temperature sensor connector.

Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
- Temperature:
- -40°C (-40°F) or more
Text in Illustration *1
Intake Air Temperature Sensor
*2
ECM
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR) |
Disconnect the intake air temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A2-2 or D100-71 (THA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
