TERMINALS OF ECU
System information · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.
- CAUTION:
- For vehicles with an airbag system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
| JUNCTION CONNECTOR |
No. 1 CAN Junction Connector


Text in Illustration *1
No. 1 CAN Junction Connector
-
-
*a
Front view of wire harness connector
(to No. 1 CAN Junction Connector)
-
-
No. 1 CAN Junction Connector
Wiring Color
Connect to
H63-1 (CANH)
B
ECM
H63-2 (CANL)
W
H66-1 (CANH)
G
Certification ECU (smart key ECU assembly)*1
H66-2 (CANL)
W
H90-1 (CANH)
P
Headlight leveling ECU assembly*2
H90-2 (CANL)
W
H93-1 (CANH)
V
Center airbag sensor assembly*3
H93-2 (CANL)
W
H94-1 (CANH)
L
Brake actuator assembly (skid control ECU)*4
H94-2 (CANL)
W
H95-1 (CANH)
W
Spiral cable sub-assembly (steering angle sensor)*5
H95-2 (CANL)
R
H96-1 (CANH)
W
No. 2 CAN junction connector
H96-2 (CANL)
B
- *1: w/ Smart Entry and Start System
- *2: for LED Headlight
- *3: w/ Airbag System
- *4: w/ ABS
- *5: w/ VSC
- *1: w/ Smart Entry and Start System
No. 2 CAN Junction Connector


Text in Illustration *1
No. 2 CAN Junction Connector
-
-
*a
Front view of wire harness connector
(to No. 2 CAN Junction Connector)
-
-
No. 2 CAN Junction Connector
Wiring Color
Connect to
H97-1 (CANH)
R
Air conditioning amplifier assembly*
H97-2 (CANL)
W
H98-1 (CANH)
Y
DLC3
H98-2 (CANL)
W
H99-1 (CANH)
B
Combination meter assembly
H99-2 (CANL)
W
H100-1 (CANH)
W
No. 1 CAN junction connector
H100-2 (CANL)
B
- *: w/ Air Conditioning System, except 5L-E
- *: w/ Air Conditioning System, except 5L-E
| CHECK DLC3 |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

Text in Illustration *a
Front view of DLC3
- CAUTION:
- For vehicles with an airbag system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
- Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
H23-6 (CANH) - H23-14 (CANL)
Y - W
Ignition switch off
54 to 69 Ω
H23-6 (CANH) - H23-4 (CG)
Y - W-B
Ignition switch off
200 Ω or higher
H23-14 (CANL) - H23-4 (CG)
W - W-B
Ignition switch off
200 Ω or higher
H23-6 (CANH) - H23-16 (BAT)
Y - B
Ignition switch off
6 kΩ or higher
H23-14 (CANL) - H23-16 (BAT)
W - B
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1KD-FTV [w/ DPF]) |


| *A |
for V1 Bus |
*B |
for Powertrain Bus |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
for V1 Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B73-7 (CANH) - B73-6 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B73-7 (CANH) - D99-109 (E1)
B - W-B
Ignition switch off
200 Ω or higher
B73-6 (CANL) - D99-109 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B73-7 (CANH) - B73-2 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B73-6 (CANL) - B73-2 (BATT)
W - W
Ignition switch off
6 kΩ or higher
for Powertrain Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
D99-40 (CAN+) - D99-63 (CAN-)
L - Y
Ignition switch off
108 to 132 Ω
D99-40 (CAN+) - D99-109 (E1)
L - W-B
Ignition switch off
200 Ω or higher
D99-63 (CAN-) - D99-109 (E1)
Y - W-B
Ignition switch off
200 Ω or higher
D99-40 (CAN+) - B73-2 (BATT)
L - W
Ignition switch off
6 kΩ or higher
D99-63 (CAN-) - B73-2 (BATT)
Y - W
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1KD-FTV [w/o DPF]) |


| *A |
for V1 Bus |
*B |
for Powertrain Bus |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
for V1 Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B72-7 (CANH) - B72-6 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B72-7 (CANH) - D98-109 (E1)
B - W-B
Ignition switch off
200 Ω or higher
B72-6 (CANL) - D98-109 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B72-7 (CANH) - B72-2 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B72-6 (CANL) - B72-2 (BATT)
W - W
Ignition switch off
6 kΩ or higher
for Powertrain Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
D98-40 (CAN+) - D98-63 (CAN-)
L - Y
Ignition switch off
108 to 132 Ω
D98-40 (CAN+) - D98-109 (E1)
L - W-B
Ignition switch off
200 Ω or higher
D98-63 (CAN-) - D98-109 (E1)
Y - W-B
Ignition switch off
200 Ω or higher
D98-40 (CAN+) - B72-2 (BATT)
L - W
Ignition switch off
6 kΩ or higher
D98-63 (CAN-) - B72-2 (BATT)
Y - W
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 2KD-FTV) |


| *A |
for V1 Bus |
*B |
for Powertrain Bus |
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
for V1 Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B88-6 (CANH) - B88-7 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B88-6 (CANH) - D105-109 (E1)
B - BR
Ignition switch off
200 Ω or higher
B88-7 (CANL) - D105-109 (E1)
W - BR
Ignition switch off
200 Ω or higher
B88-6 (CANH) - B88-2 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B88-7 (CANL) - B88-2 (BATT)
W - W
Ignition switch off
6 kΩ or higher
for Powertrain Bus Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B88-4 (CAN+) - B88-5 (CAN-)
L - Y
Ignition switch off
108 to 132 Ω
B88-4 (CAN+) - D105-109 (E1)
L - BR
Ignition switch off
200 Ω or higher
B88-5 (CAN-) - D105-109 (E1)
Y - BR
Ignition switch off
200 Ω or higher
B88-4 (CAN+) - B88-2 (BATT)
L - W
Ignition switch off
6 kΩ or higher
B88-5 (CAN-) - B88-2 (BATT)
Y - W
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 1TR-FE, 2TR-FE [w/ Dual VVT-i]) |


Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B94-13 (CANH) - B94-26 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B94-13 (CANH) - D116-59 (E1)
B - W-B
Ignition switch off
200 Ω or higher
B94-26 (CANL) - D116-59 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B94-13 (CANH) - B94-1 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B94-26 (CANL) - B94-1 (BATT)
W - W
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 2TR-FE [w/o Dual VVT-i]) |


Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B71-8 (CANH) - B71-9 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B71-8 (CANH) - D97-105 (E1)
B - W-B
Ignition switch off
200 Ω or higher
B71-9 (CANL) - D97-105 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B71-8 (CANH) - B71-20 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B71-9 (CANL) - B71-20 (BATT)
W - W
Ignition switch off
6 kΩ or higher
| CHECK ECM (for 5L-E) |


Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B74-10 (CANH) - B74-11 (CANL)
B - W
Ignition switch off
108 to 132 Ω
B74-10 (CANH) - D100-109 (E1)
B - W-B
Ignition switch off
200 Ω or higher
B74-11 (CANL) - D100-109 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B74-10 (CANH) - B74-2 (BATT)
B - W
Ignition switch off
6 kΩ or higher
B74-11 (CANL) - B74-2 (BATT)
W - W
Ignition switch off
6 kΩ or higher
| CHECK COMBINATION METER ASSEMBLY |


Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
H20-23 (CANH) - H20-22 (CANL)
B - W
Ignition switch off
108 to 132 Ω
H20-23 (CANH) - H20-21 (E1)
B - W-B
Ignition switch off
200 Ω or higher
H20-22 (CANL) - H20-21 (E1)
W - W-B
Ignition switch off
200 Ω or higher
H20-23 (CANH) - H20-1 (L)
B - R
Ignition switch off
6 kΩ or higher
H20-22 (CANL) - H20-1 (L)
W - R
Ignition switch off
6 kΩ or higher
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Air Conditioning System, except 5L-E) |


Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
H18-10 (CANH) - H18-11 (CANL)
R - W
Ignition switch off
54 to 69 Ω
H18-10 (CANH) - H18-29 (GND)
R - W-B
Ignition switch off
200 Ω or higher
H18-11 (CANL) - H18-29 (GND)
W - W-B
Ignition switch off
200 Ω or higher
H18-10 (CANH) - H18-40 (B)
R - W
Ignition switch off
6 kΩ or higher
H18-11 (CANL) - H18-40 (B)
W - W
Ignition switch off
6 kΩ or higher
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System) |


Disconnect the certification ECU (smart key ECU assembly) connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B76-40 (CANH) - B76-18 (CANL)
G - W
Ignition switch off
54 to 69 Ω
B76-40 (CANH) - B75-10 (E)
G - W-B
Ignition switch off
200 Ω or higher
B76-18 (CANL) - B75-10 (E)
W - W-B
Ignition switch off
200 Ω or higher
B76-40 (CANH) - B75-1 (+B)
G - L
Ignition switch off
6 kΩ or higher
B76-18 (CANL) - B75-1 (+B)
W - L
Ignition switch off
6 kΩ or higher
| CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight) |


Disconnect the headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
A39-6 (CANH) - A39-7 (CANL)
P - W
Ignition switch off
54 to 69 Ω
A39-6 (CANH) - A39-9 (E1)
P - W-B
Ignition switch off
200 Ω or higher
A39-7 (CANL) - A39-9 (E1)
W - W-B
Ignition switch off
200 Ω or higher
A39-6 (CANH) - H23-16 (BAT)
P - B
Ignition switch off
6 kΩ or higher
A39-7 (CANL) - H23-16 (BAT)
W - B
Ignition switch off
6 kΩ or higher
| CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC) |


Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B92-22 (CANH) - B92-10 (CANL)
L - W
Ignition switch off
54 to 69 Ω
B92-22 (CANH) - B92-25 (GND1)
L - W-B
Ignition switch off
200 Ω or higher
B92-10 (CANL) - B92-25 (GND1)
W - W-B
Ignition switch off
200 Ω or higher
B92-22 (CANH) - B92-13 (+BM)
L - W
Ignition switch off
6 kΩ or higher
B92-10 (CANL) - B92-13 (+BM)
W - W
Ignition switch off
6 kΩ or higher
| CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC) |


Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B19-6 (CANH) - B19-5 (CANL)
L - W
Ignition switch off
54 to 69 Ω
B19-6 (CANH) - B19-2 (GND)
L - W-B
Ignition switch off
200 Ω or higher
B19-5 (CANL) - B19-2 (GND)
W - W-B
Ignition switch off
200 Ω or higher
B19-6 (CANH) - B19-23 (+BM)
L - W
Ignition switch off
6 kΩ or higher
B19-5 (CANL) - B19-23 (+BM)
W - W
Ignition switch off
6 kΩ or higher
| CHECK CENTER AIRBAG SENSOR ASSEMBLY (w/ Airbag System) |


Disconnect the center airbag sensor assembly connector (Click here).
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
B4-13 (CANH) - B4-22 (CANL)
V - W
Ignition switch off
54 to 69 Ω
B4-13 (CANH) - B4-25 (E1)
V - W-B
Ignition switch off
200 Ω or higher
B4-22 (CANL) - B4-25 (E1)
W - W-B
Ignition switch off
200 Ω or higher
B4-13 (CANH) - H23-16 (BAT)
V - B
Ignition switch off
6 kΩ or higher
B4-22 (CANL) - H23-16 (BAT)
W - B
Ignition switch off
6 kΩ or higher
| CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC) |
![]() ![]() |
Disconnect the spiral cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
H92-3 (CANH) - H92-2 (CANL)
W - R
Ignition switch off
54 to 69 Ω
H92-3 (CANH) - H92-1 (ESS)
W - W-B
Ignition switch off
200 Ω or higher
H92-2 (CANL) - H92-1 (ESS)
R - W-B
Ignition switch off
200 Ω or higher
H92-3 (CANH) - H92-5 (BAT)
W - W
Ignition switch off
6 kΩ or higher
H92-2 (CANL) - H92-5 (BAT)
R - W
Ignition switch off
6 kΩ or higher
| CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 1KD-FTV, 2KD-FTV and Automatic Transmission) |


Disconnect the transmission control ECU assembly connectors.
Measure the resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Switch Condition
Specified Condition
O3-21 (CAN+) - O3-20 (CAN-)
L - Y
Ignition switch off
108 to 132 Ω
O3-21 (CAN+) - O1-1 (E1)
L - W-B
Ignition switch off
200 Ω or higher
O3-20 (CAN-) - O1-1 (E1)
Y - W-B
Ignition switch off
200 Ω or higher
O3-21 (CAN+) - O3-5 (BATT)
L - B
Ignition switch off
6 kΩ or higher
O3-20 (CAN-) - O3-5 (BATT)
Y - B
Ignition switch off
6 kΩ or higher
