2014-2019 Hiace · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


JUNCTION CONNECTOR

  1. No. 1 CAN Junction Connector
    C317038E01

    Text in Illustration 
    *1
    No. 1 CAN Junction Connector
    -
    -
    *a
    Front view of wire harness connector
    (to No. 1 CAN Junction Connector)
    -
    -
    No. 1 CAN Junction Connector
    Wiring Color
    Connect to
    H63-1 (CANH)
    B
    ECM
    H63-2 (CANL)
    W
    H66-1 (CANH)
    G
    Certification ECU (smart key ECU assembly)*1
    H66-2 (CANL)
    W
    H90-1 (CANH)
    P
    Headlight leveling ECU assembly*2
    H90-2 (CANL)
    W
    H93-1 (CANH)
    V
    Center airbag sensor assembly*3
    H93-2 (CANL)
    W
    H94-1 (CANH)
    L
    Brake actuator assembly (skid control ECU)*4
    H94-2 (CANL)
    W
    H95-1 (CANH)
    W
    Spiral cable sub-assembly (steering angle sensor)*5
    H95-2 (CANL)
    R
    H96-1 (CANH)
    W
    No. 2 CAN junction connector
    H96-2 (CANL)
    B
    1. *1: w/ Smart Entry and Start System
    2. *2: for LED Headlight
    3. *3: w/ Airbag System
    4. *4: w/ ABS
    5. *5: w/ VSC

  2. No. 2 CAN Junction Connector
    C317039E01

    Text in Illustration 
    *1
    No. 2 CAN Junction Connector
    -
    -
    *a
    Front view of wire harness connector
    (to No. 2 CAN Junction Connector)
    -
    -
    No. 2 CAN Junction Connector
    Wiring Color
    Connect to
    H97-1 (CANH)
    R
    Air conditioning amplifier assembly*
    H97-2 (CANL)
    W
    H98-1 (CANH)
    Y
    DLC3
    H98-2 (CANL)
    W
    H99-1 (CANH)
    B
    Combination meter assembly
    H99-2 (CANL)
    W
    H100-1 (CANH)
    W
    No. 1 CAN junction connector
    H100-2 (CANL)
    B
    1. *: w/ Air Conditioning System, except 5L-E


CHECK DLC3

  1. C253362E34
    Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.
    Text in Illustration 
    *a
    Front view of DLC3

    CAUTION:
    For vehicles with an airbag system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H23-6 (CANH) - H23-14 (CANL)
    Y - W
    Ignition switch off
    54 to 69 Ω
    H23-6 (CANH) - H23-4 (CG)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    H23-14 (CANL) - H23-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H23-6 (CANH) - H23-16 (BAT)
    Y - B
    Ignition switch off
    6 kΩ or higher
    H23-14 (CANL) - H23-16 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV [w/ DPF])
C234965E03
Text in Illustration 
*A
for V1 Bus
*B
for Powertrain Bus
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B73-7 (CANH) - B73-6 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B73-7 (CANH) - D99-109 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B73-6 (CANL) - D99-109 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B73-7 (CANH) - B73-2 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B73-6 (CANL) - B73-2 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher
    for Powertrain Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D99-40 (CAN+) - D99-63 (CAN-)
    L - Y
    Ignition switch off
    108 to 132 Ω
    D99-40 (CAN+) - D99-109 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    D99-63 (CAN-) - D99-109 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    D99-40 (CAN+) - B73-2 (BATT)
    L - W
    Ignition switch off
    6 kΩ or higher
    D99-63 (CAN-) - B73-2 (BATT)
    Y - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1KD-FTV [w/o DPF])
C234965E04
Text in Illustration 
*A
for V1 Bus
*B
for Powertrain Bus
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B72-7 (CANH) - B72-6 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B72-7 (CANH) - D98-109 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B72-6 (CANL) - D98-109 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B72-7 (CANH) - B72-2 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B72-6 (CANL) - B72-2 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher
    for Powertrain Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D98-40 (CAN+) - D98-63 (CAN-)
    L - Y
    Ignition switch off
    108 to 132 Ω
    D98-40 (CAN+) - D98-109 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    D98-63 (CAN-) - D98-109 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    D98-40 (CAN+) - B72-2 (BATT)
    L - W
    Ignition switch off
    6 kΩ or higher
    D98-63 (CAN-) - B72-2 (BATT)
    Y - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 2KD-FTV)
C234965E05
Text in Illustration 
*A
for V1 Bus
*B
for Powertrain Bus
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B88-6 (CANH) - B88-7 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B88-6 (CANH) - D105-109 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    B88-7 (CANL) - D105-109 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    B88-6 (CANH) - B88-2 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B88-7 (CANL) - B88-2 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher
    for Powertrain Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B88-4 (CAN+) - B88-5 (CAN-)
    L - Y
    Ignition switch off
    108 to 132 Ω
    B88-4 (CAN+) - D105-109 (E1)
    L - BR
    Ignition switch off
    200 Ω or higher
    B88-5 (CAN-) - D105-109 (E1)
    Y - BR
    Ignition switch off
    200 Ω or higher
    B88-4 (CAN+) - B88-2 (BATT)
    L - W
    Ignition switch off
    6 kΩ or higher
    B88-5 (CAN-) - B88-2 (BATT)
    Y - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1GD-FTV)
A247842E88
Text in Illustration 
*A
for V1 Bus
*B
for Local Bus
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    for V1 Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B97-13 (CANH) - B97-26 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B97-13 (CANH) - D134-21 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B97-26 (CANL) - D134-21 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B97-13 (CANH) - B97-1 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B97-26 (CANL) - B97-1 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher
    for Local Bus 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B97-41 (CANU) - B97-56 (CAND)
    L - Y
    Ignition switch off
    108 to 132 Ω
    B97-41 (CANU) - D134-21 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    B97-56 (CAND) - D134-21 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    B97-41 (CANU) - B97-1 (BATT)
    L - W
    Ignition switch off
    6 kΩ or higher
    B97-56 (CAND) - B97-1 (BATT)
    Y - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 1TR-FE, 2TR-FE [w/ Dual VVT-i])
A247842E60
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B94-13 (CANH) - B94-26 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B94-13 (CANH) - D116-59 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B94-26 (CANL) - D116-59 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B94-13 (CANH) - B94-1 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B94-26 (CANL) - B94-1 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 2TR-FE [w/o Dual VVT-i])
C234965E06
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B71-8 (CANH) - B71-9 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B71-8 (CANH) - D97-105 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B71-9 (CANL) - D97-105 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B71-8 (CANH) - B71-20 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B71-9 (CANL) - B71-20 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK ECM (for 5L-E)
C234965E07
  1. Disconnect the ECM connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B74-10 (CANH) - B74-11 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    B74-10 (CANH) - D100-109 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    B74-11 (CANL) - D100-109 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B74-10 (CANH) - B74-2 (BATT)
    B - W
    Ignition switch off
    6 kΩ or higher
    B74-11 (CANL) - B74-2 (BATT)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK COMBINATION METER ASSEMBLY
E161130E30
  1. Disconnect the combination meter assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H20-23 (CANH) - H20-22 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    H20-23 (CANH) - H20-21 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    H20-22 (CANL) - H20-21 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H20-23 (CANH) - H20-1 (L)
    B - R
    Ignition switch off
    6 kΩ or higher
    H20-22 (CANL) - H20-1 (L)
    W - R
    Ignition switch off
    6 kΩ or higher


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Air Conditioning System, except 5L-E)
E161130E31
  1. Disconnect the air conditioning amplifier assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H18-10 (CANH) - H18-11 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    H18-10 (CANH) - H18-29 (GND)
    R - W-B
    Ignition switch off
    200 Ω or higher
    H18-11 (CANL) - H18-29 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H18-10 (CANH) - H18-40 (B)
    R - W
    Ignition switch off
    6 kΩ or higher
    H18-11 (CANL) - H18-40 (B)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)
C297946E02
  1. Disconnect the certification ECU (smart key ECU assembly) connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B76-40 (CANH) - B76-18 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    B76-40 (CANH) - B75-10 (E)
    G - W-B
    Ignition switch off
    200 Ω or higher
    B76-18 (CANL) - B75-10 (E)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B76-40 (CANH) - B75-1 (+B)
    G - L
    Ignition switch off
    6 kΩ or higher
    B76-18 (CANL) - B75-1 (+B)
    W - L
    Ignition switch off
    6 kΩ or higher


CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight)
C217402E10
  1. Disconnect the headlight leveling ECU assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A39-6 (CANH) - A39-7 (CANL)
    P - W
    Ignition switch off
    54 to 69 Ω
    A39-6 (CANH) - A39-9 (E1)
    P - W-B
    Ignition switch off
    200 Ω or higher
    A39-7 (CANL) - A39-9 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A39-6 (CANH) - H23-16 (BAT)
    P - B
    Ignition switch off
    6 kΩ or higher
    A39-7 (CANL) - H23-16 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC)
C306841E02
  1. Disconnect the brake actuator assembly (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B92-22 (CANH) - B92-10 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    B92-22 (CANH) - B92-25 (GND1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    B92-10 (CANL) - B92-25 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B92-22 (CANH) - B92-13 (+BM)
    L - W
    Ignition switch off
    6 kΩ or higher
    B92-10 (CANL) - B92-13 (+BM)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC)
C111164E07
  1. Disconnect the brake actuator assembly (skid control ECU) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B19-6 (CANH) - B19-5 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    B19-6 (CANH) - B19-2 (GND)
    L - W-B
    Ignition switch off
    200 Ω or higher
    B19-5 (CANL) - B19-2 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B19-6 (CANH) - B19-23 (+BM)
    L - W
    Ignition switch off
    6 kΩ or higher
    B19-5 (CANL) - B19-23 (+BM)
    W - W
    Ignition switch off
    6 kΩ or higher


CHECK CENTER AIRBAG SENSOR ASSEMBLY (w/ Airbag System)
C317040E01
  1. Disconnect the center airbag sensor assembly connector (Click here).

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    B4-13 (CANH) - B4-22 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    B4-13 (CANH) - B4-25 (E1)
    V - W-B
    Ignition switch off
    200 Ω or higher
    B4-22 (CANL) - B4-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    B4-13 (CANH) - H23-16 (BAT)
    V - B
    Ignition switch off
    6 kΩ or higher
    B4-22 (CANL) - H23-16 (BAT)
    W - B
    Ignition switch off
    6 kΩ or higher


CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC)
C306881E01
  1. Disconnect the spiral cable sub-assembly (steering angle sensor) connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    H92-3 (CANH) - H92-2 (CANL)
    W - R
    Ignition switch off
    54 to 69 Ω
    H92-3 (CANH) - H92-1 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    H92-2 (CANL) - H92-1 (ESS)
    R - W-B
    Ignition switch off
    200 Ω or higher
    H92-3 (CANH) - H92-5 (BAT)
    W - W
    Ignition switch off
    6 kΩ or higher
    H92-2 (CANL) - H92-5 (BAT)
    R - W
    Ignition switch off
    6 kΩ or higher


CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 1KD-FTV, 2KD-FTV and Automatic Transmission)
C253536E05
  1. Disconnect the transmission control ECU assembly connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    O3-21 (CAN+) - O3-20 (CAN-)
    L - Y
    Ignition switch off
    108 to 132 Ω
    O3-21 (CAN+) - O1-1 (E1)
    L - W-B
    Ignition switch off
    200 Ω or higher
    O3-20 (CAN-) - O1-1 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    O3-21 (CAN+) - O3-5 (BATT)
    L - B
    Ignition switch off
    6 kΩ or higher
    O3-20 (CAN-) - O3-5 (BATT)
    Y - B
    Ignition switch off
    6 kΩ or higher

← TERMINALS OF ECU (Apr 2016 – Dec 2016)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →