2014-2019 Hiace · Service Manual ENGINE

Pre-heating Control Circuit

Circuit diagnosis · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval for the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the GLOW relay and permits the current to flow through the glow plug based on the calculated time of the ECM. The GLOW relay is then heated, and enhances fuel combustion with a cold engine.
This DTC will be set if the glow plug or the circuit is open.
A255090E03

HINT:
  1. These troubleshooting procedures are for the following conditions: 1) difficulty starting the engine in cold weather, and 2) difficulty driving the vehicle or vehicle malfunctions in cold weather immediately after engine is started.
  2. After the engine is started, the ECM performs an "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.

G038988E01

WIRING DIAGRAM

A319080E01

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. INSPECT GLOW RELAY
  1. Inspect the glow plug relay (GLOW) (Click here).



NG
REPLACE GLOW RELAY
OK


2. INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
  1. Inspect the glow plug (Click here).



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


3. CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
  1. Check the glow plug installation.

    OK:
    Glow plugs are installed securely.

Torque:
13 N*m{ 130 kgf*cm , 10 ft.*lbf }



NG
TIGHTEN GLOW PLUG
OK


4. CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)
  1. Disconnect the ECM connector.

  1. Remove the GLOW relay from the No. 1 engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D105-58 (GREL) - GLOW relay (1)
    Always
    Below 1 Ω
    GLOW relay (2) - Body ground
    Always
    Below 1 Ω
    D105-58 (GREL) or GLOW relay (1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the GLOW relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (GLOW RELAY - GLOW PLUG AND BATTERY)
  1. Remove the GLOW relay from the No. 1 engine room relay block and junction block assembly.

  1. Disconnect the glow plug connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    GLOW relay (5) - D80-1
    Always
    Below 1 Ω
    GLOW relay (3) - Positive (+) battery terminal cable
    Always
    Below 1 Ω
    GLOW relay (5) or D80-1 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the GLOW relay.

  1. Reconnect the glow plug connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Pre-heating Control Circuit (Apr 2016 – Dec 2016)Rough Idling or Excessive Engine Vibrations (Oct 2014 – Dec 2014) →