DATA LIST / ACTIVE TEST
System information · Vehicles built Oct 2014 – Dec 2014
| READ DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
N Range Status
Shift lever N status/
ON or OFF
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
SPD (NC0)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
- Lock-up ON (after warming up engine): Input turbine speed (NC0) equal to engine speed
- Lock-up OFF (idling with shift lever in N): Input turbine speed (NC0) nearly equal to engine speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed)
-
Shift SW Status (P Range)
PNP switch status/
ON or OFF
- Shift lever in P: ON
- Shift lever not in P: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (R Range)
PNP switch status/
ON or OFF
- Shift lever in R: ON
- Shift lever not in R: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
- Shift lever in 2: ON
- Shift lever not in 2: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (L Range)
PNP switch status/
ON or OFF
- Shift lever in L: ON
- Shift lever not in L: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N Range)
PNP switch status/
ON or OFF
- Shift lever in N: ON
- Shift lever not in N: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (N, P Range) Supported
Status of PNP switch (N or P) supported/
Supp or Unsupp
-
-
Shift SW Status (N, P Range)
PNP switch status/
ON or OFF
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
-
Shift SW Status (D Range)
PNP switch status/
ON or OFF
- Shift lever in D or 3: ON
- Shift lever not in D or 3: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
- Shift lever in 3: ON
- Shift lever not in 3: OFF
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. - HINT:
- When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).
A/T Oil Temperature 3
ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 215°C (419°F)
- After stall test: Approximately 80°C (176°F)
- Equal to ambient temperature when engine cold
If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted.
Lock Up
Lock up/
ON or OFF
- Lock-up is operating: ON
- Lock-up is not operating: OFF
-
Lock Up Solenoid Status
Shift solenoid SL status/
ON or OFF
- Shift solenoid SL is operating: ON
- Shift solenoid SL is not operating: OFF
-
Shift Status
ECM gear shift command/
1st, 2nd, 3rd or 4th
- Shift lever in D: 1st, 2nd, 3rd or 4th
- Shift lever in 3: 1st, 2nd or 3rd
- Shift lever in 2: 1st or 2nd
- Shift lever in L: 1st
-
SLT Solenoid Status
Shift solenoid SLT status/
ON or OFF
- Accelerator pedal depressed: OFF
- Accelerator pedal released: ON
-
Snow or 2nd Start Mode
Pattern select switch status/
ON or OFF
OFF
-
- Shift lever in P or N: ON
| PERFORM ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Connect the TC and TE1
Connects and disconnects TC and TE1
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Shift lever in P or N
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off)
[Vehicle Condition] - Vehicle stopped
- Engine idling
Activate the Solenoid (S1)
Operate the shift solenoid S1
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Activate the Solenoid (S2)
Operate the shift solenoid S2
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Activate the Lock Up
Control shift solenoid valve SL to set automatic transmission to lock-up condition
ON or OFF
Possible to check shift solenoid valve SL operation.
[Vehicle Condition]- Throttle valve opening angle: Less than 35%
- Vehicle speed: 60 km/h (37 mph) or more
Activate the Solenoid (SL)
Operate the shift solenoid SL
ON or OFF
[Vehicle Condition] - Ignition switch ON
- Engine is stopped
- Shift lever in P or N
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less
- HINT:
- *: The Active Test "Activate the Solenoid (SLT)" is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.
- Ignition switch ON