P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
SYSTEM DESCRIPTION
The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2714 |
The ECM detects a malfunction in the shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and the output shaft, and also by the ATF pressure. (2 trip detection logic) |
|
MONITOR DESCRIPTION
The ECM calculates the amount of clutch slip based on the input turbine speed, output shaft speed, and gear ratio. If the amount of clutch slip exceeds a specified level, the ECM will set this DTC and illuminate the MIL.When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.
- NOTICE:
- If the vehicle continues to be driven under these conditions, the clutch will burn up and the vehicle will no longer be drivable.
INSPECTION PROCEDURE
- NOTICE:
- Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).
| 1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
Result Result
Proceed to
Only DTC P2714 is output
A
P2714 and other DTCs are output
B
- HINT:
- If a solenoid is stuck on, DTCs for several solenoids including the malfunctioning solenoid will be detected.
|
|
||||
| B | |
| 2. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE SOLENOID (SLT)) |
- NOTICE:
- Perform the test while the ATF (Automatic Transmission Fluid) temperature is between 50 and 80°C (122 and 176°F).
- Be careful to prevent the hose of SST from interfering with the exhaust pipe.
- This check must be conducted after checking and adjusting the engine.
- Perform the test with the air conditioning off.
- Perform the test while the ATF (Automatic Transmission Fluid) temperature is between 50 and 80°C (122 and 176°F).
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Lift the vehicle up.
Remove the test plug from the transmission case and connect SST.

- SST
- 09992-00095
(09992-00231, 09992-00271)
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the GTS to the DLC3.
Start the engine.
Warm up the ATF (Automatic Transmission Fluid).
Measure the line pressure when the engine is idling.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Follow the instructions on the GTS and perform the Active Test.
Measure the line pressure with SST.
*: The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Solenoid (SLT)*
Operates shift solenoid valve SLT to raise the line pressure.
ON/OFF - HINT:
- ON: No action (normal operation)
- OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off).
[Vehicle Condition] - Vehicle Stopped
- Engine idling
- HINT:
- Note that the pressure readings for the Active Test and Hydraulic Test are different.
- OK:
- The line pressure changes as specified when performing the Active Test.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION) |
- NOTICE:
- This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
- HINT:
- Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).
Engine and ECT Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operates the shift solenoid valves to allow gears to be selected manually.
- Press "→" button: Up-shift occurs
- Press "←" button: Down-shift occurs
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 seconds interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transmission.
[Vehicle Condition]- 50 km/h (31 mph) or less
- HINT:
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
- The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.
- The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.
- Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
- The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.
- This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
Compare the ECM commanded gear and the actual gear.
- Result:
Actual Gear during Malfunction
ECM Commanded Gear
Proceed to
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL1
Stuck ON
1st
2nd
3rd
4th
4th
4th
A
Stuck OFF
N*1
N*1
N*1
N*1
5th
6th
Shift solenoid valve SL2
Stuck ON
4th
4th
4th
4th
5th
6th
B
Stuck OFF
1st
2nd
3rd
1st
N*1
N*1
Shift solenoid valve SL3
Stuck ON
2nd
2nd
3rd
4th
5th
6th
C
Stuck OFF
1st
1st
3rd
4th
5th
N*1
Shift solenoid valve SL4
Stuck ON
3rd
3rd
3rd
4th
5th
5th
D
Stuck OFF
1st
2nd
1st
4th
N*1
6th
Shift solenoid valve SLT
Stuck ON
N*2
N*2
N*2
N*2
N*2
N*2
E
Stuck OFF*3
1st
2nd
3rd
4th
5th
6th
- HINT:
- *1: Neutral
- *2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
- *3: When shift solenoid valve SLT is stuck off, gear shifting is normal.
- *1: Neutral
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 4. INSPECT SHIFT SOLENOID VALVE SLT |
Remove shift solenoid valve SLT (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *1 |
Shift Solenoid Valve SLT |
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There is no foreign matter on each valve and they operate smoothly.
|
|
||||
| OK | ||
| ||
