INSTALLATION
Removal / installation · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| 1. INSTALL ROOF HEADLINING NO. 1 (for High Roof) |
| 2. INSTALL ROOF HEADLINING NO. 1 (for Middle Roof) |
| 3. INSTALL REAR COOLER CONTROL PANEL |
| 4. INSTALL MAP LIGHT ASSEMBLY (Super Wagon) |
| 5. INSTALL ROOM LIGHT ASSEMBLY NO. 1 (Deluxe) |
| 6. INSTALL VISOR HOLDER |
| 7. INSTALL VISOR ASSEMBLY LH |
| 8. INSTALL VISOR ASSEMBLY RH |
| 9. INSTALL ASSIST GRIP |
| 10. INSTALL FRONT PILLAR GARNISH RH |
| 11. INSTALL FRONT PILLAR GARNISH LH |
| 12. INSTALL ASSIST GRIP ASSEMBLY |
| 13. INSTALL FRONT ASSIST GRIP PLUG NO. 1 |
| 14. INSTALL ROOF HEADLINING NO. 2 (for High Roof) |
| 15. INSTALL ROOF HEADLINING NO. 2 (for Middle Roof) |
| 16. INSTALL REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass) |
| 17. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Super Wagon) |
| 18. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Deluxe) |
| 19. INSTALL REAR SEAT HOOK (for Space Up Seat) |
| 20. INSTALL ROOF SIDE GARNISH INNER UPPER RH |
| 21. INSTALL ROOF SIDE GARNISH INNER UPPER LH |
| 22. INSTALL QUARTER PILLAR GARNISH RH (for Middle Roof) |
| 23. INSTALL QUARTER PILLAR GARNISH LH (for Middle Roof) |
| 24. INSTALL QUARTER PILLAR GARNISH RH (for High Roof) |
| 25. INSTALL QUARTER PILLAR GARNISH LH (for High Roof) |
| 26. INSTALL CENTER PILLAR GARNISH RH |
| 27. INSTALL CENTER PILLAR GARNISH LOWER RH |
| 28. INSTALL ASSIST GRIP ASSEMBLY REAR |
| 29. INSTALL ASSIST GRIP PLUG |
| 30. INSTALL CENTER PILLAR GARNISH LH |
| 31. INSTALL ENGINE SERVICE HOLE COVER HOOK NO. 2 LH |
| 32. INSTALL SIDE NO. 1 TRIM ASSEMBLY LH |
| 33. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR RH |
| 34. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for High Roof) |
| 35. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for Middle Roof) |
| 36. INSTALL BACK DOOR WEATHERSTRIP |
| 37. INSTALL BACK DOOR SCUFF PLATE |
| 38. INSTALL SLIDE DOOR WEATHERSTRIP NO. 1 RH |
| 39. INSTALL REAR DOOR SCUFF PLATE RH |
| 40. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
Connect the front seat outer belt assembly LH with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to close the cover.

Connect the front seat outer belt assembly LH with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 41. INSTALL SEAT BELT ANCHOR COVER |
| 42. INSTALL SEAT ASSEMBLY LH |
| 43. INSTALL CENTER PILLAR GARNISH COVER LOWER LH |
| 44. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
Connect the front seat outer belt assembly RH with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to close the cover.

Connect the front seat outer belt assembly RH with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
| 45. INSTALL FRONT DOOR OPENING TRIM RH |
| 46. INSTALL FRONT DOOR OPENING TRIM LH |
| 47. INSTALL FRONT DOOR SCUFF PLATE RH |
| 48. INSTALL FRONT DOOR SCUFF PLATE LH |
| 49. INSTALL REAR NO. 4 SEAT BELT ASSEMBLY OUTER |
Check the degree of tilt when the ELR begins to lock.

Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlocked
*b
Locked
*c
45°
Install the rear No. 4 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 4 claws to install the retractor cover of the rear No. 4 seat belt assembly outer.

Connect the shoulder side of the rear No. 4 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to close the shoulder side cover of the rear No. 4 seat belt assembly outer.

Connect the floor side of the rear No. 4 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Check if the ELR locks.
- NOTICE:
- This check should be performed with the rear No. 4 seat belt assembly outer installed.
With the rear No. 4 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
If operation is not as specified, replace the rear No. 4 seat belt assembly outer.
| 50. INSTALL REAR NO. 3 SEAT BELT ASSEMBLY OUTER |
Check the degree of tilt when the ELR begins to lock.

Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlocked
*b
Locked
*c
45°
Install the rear No. 3 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 4 claws to install the retractor cover of the rear No. 3 seat belt assembly outer.

Tighten the bolt to connect the shoulder side of the rear No. 3 seat belt assembly outer.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 4 claws to close the shoulder side cover of the rear No. 3 seat belt assembly outer.

Connect the floor side of the rear No. 3 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Check if the ELR locks.
- NOTICE:
- This check should be performed with the rear No. 3 seat belt assembly outer installed.
With the rear No. 3 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
If operation is not as specified, replace the rear No. 3 seat belt assembly outer.
| 51. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY OUTER |
Check the degree of tilt when the ELR begins to lock.

Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlocked
*b
Locked
*c
45°
Install the rear No. 2 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Connect the shoulder side of the rear No. 2 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to close the shoulder side cover of the rear No. 2 seat belt assembly outer.

Connect the floor side of the rear No. 2 seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Check if the ELR locks.
- NOTICE:
- This check should be performed with the rear No. 2 seat belt assembly outer installed.
With the rear No. 2 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
If operation is not as specified, replace the rear No. 2 seat belt assembly outer.
| 52. INSTALL REAR SEAT BELT ASSEMBLY OUTER |
Check the degree of tilt when the ELR begins to lock.

Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.
- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlocked
*b
Locked
*c
45°
Tighten the bolt to install the rear seat belt assembly outer.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 4 claws to close the shoulder side cover of the rear seat belt assembly outer.

Connect the floor side of the rear seat belt assembly outer with the bolt.

- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
for Rear No. 1 Seat Bench Seat Type:
Check the degree of tilt when the ELR begins to lock.

Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.- NOTICE:
- Do not disassemble the retractor.
Text in Illustration *a
Unlocked
*b
Locked
*c
45°
w/ Cover:
- Install the side trim cover to the rear seat belt assembly outer.
- Install the bolt to the floor side of the rear seat belt assembly outer.
- Install the side trim cover to the rear seat belt assembly outer.
Temporarily install the rear seat belt assembly outer with the 2 bolts.

Tighten the lower side bolt first, and then tighten the upper side bolt to install the rear seat belt assembly outer.
- Torque:
- for Upper Bolt:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
- for Lower Bolt:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to install the retractor cover of the rear seat belt assembly outer.
Tighten the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Attach the 2 claws to close the shoulder side cover of the rear seat belt assembly outer.
Tighten the bolt to connect the floor side of the rear seat belt assembly outer.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
w/ Cover:
Attach the 3 guides and 3 claws to install the side trim cover.
Check if the ELR locks.
- NOTICE:
- This check should be performed with the rear seat belt assembly outer installed.
With the rear seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
If operation is not as specified, replace the rear seat belt assembly outer.
| 53. INSTALL REAR NO. 4 SEAT ASSEMBLY |
Secure the rear No.4 seat assembly with the 2 locks

Install the rear No.4 seat assembly with the 3 bolts and 2 nuts.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
- NOTICE:
- After installing the rear No.4 seat assembly, fold down the seatback onto the seat cushion, lift the side of the rear No.4 seat assembly, and drop it to engage the locks securely.
| 54. INSTALL REAR NO. 3 SEAT ASSEMBLY |
for Bench Type Seatback:
Install the rear No. 3 seat assembly (Click here).
for Separate Type Seatback:
Install the rear No. 3 seat assembly (Click here).
| 55. INSTALL REAR NO. 2 SEAT ASSEMBLY |
Install the rear No.2 seat assembly with the 4 bolts and 2 nuts.

- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
- HINT:
- Use the same procedure for the second row.
- Use the same procedure for the third row.
- Use the same procedure for the second row.
| 56. INSTALL REAR NO. 1 SEAT ASSEMBLY |
First row:

Install the rear No.1 seat assembly with the 3 bolts and nut.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
Second row:

Install the rear No.1 seat assembly with the 2 bolts and 2 nuts.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
| 57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
