2014-2019 Hiace · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. INSTALL ROOF HEADLINING NO. 1 (for High Roof)

2. INSTALL ROOF HEADLINING NO. 1 (for Middle Roof)

3. INSTALL REAR COOLER CONTROL PANEL

4. INSTALL MAP LIGHT ASSEMBLY (Super Wagon)

5. INSTALL ROOM LIGHT ASSEMBLY NO. 1 (Deluxe)

6. INSTALL VISOR HOLDER

7. INSTALL VISOR ASSEMBLY LH

8. INSTALL VISOR ASSEMBLY RH

9. INSTALL ASSIST GRIP

10. INSTALL FRONT PILLAR GARNISH RH

11. INSTALL FRONT PILLAR GARNISH LH

12. INSTALL ASSIST GRIP ASSEMBLY

13. INSTALL FRONT ASSIST GRIP PLUG NO. 1

14. INSTALL ROOF HEADLINING NO. 2 (for High Roof)

15. INSTALL ROOF HEADLINING NO. 2 (for Middle Roof)

16. INSTALL REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass)

17. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Super Wagon)

18. INSTALL ROOM LIGHT ASSEMBLY NO. 2 (Deluxe)

19. INSTALL REAR SEAT HOOK (for Space Up Seat)

20. INSTALL ROOF SIDE GARNISH INNER UPPER RH

21. INSTALL ROOF SIDE GARNISH INNER UPPER LH

22. INSTALL QUARTER PILLAR GARNISH RH (for Middle Roof)

23. INSTALL QUARTER PILLAR GARNISH LH (for Middle Roof)

24. INSTALL QUARTER PILLAR GARNISH RH (for High Roof)

25. INSTALL QUARTER PILLAR GARNISH LH (for High Roof)

26. INSTALL CENTER PILLAR GARNISH RH

27. INSTALL CENTER PILLAR GARNISH LOWER RH

28. INSTALL ASSIST GRIP ASSEMBLY REAR

29. INSTALL ASSIST GRIP PLUG

30. INSTALL CENTER PILLAR GARNISH LH

31. INSTALL ENGINE SERVICE HOLE COVER HOOK NO. 2 LH

32. INSTALL SIDE NO. 1 TRIM ASSEMBLY LH

33. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR RH

34. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for High Roof)

35. INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH (for Middle Roof)

36. INSTALL BACK DOOR WEATHERSTRIP

37. INSTALL BACK DOOR SCUFF PLATE

38. INSTALL SLIDE DOOR WEATHERSTRIP NO. 1 RH

39. INSTALL REAR DOOR SCUFF PLATE RH

40. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B103246
    Connect the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B115749
    Attach the 2 claws to close the cover.

  1. B103256
    Connect the front seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


41. INSTALL SEAT BELT ANCHOR COVER

42. INSTALL SEAT ASSEMBLY LH

43. INSTALL CENTER PILLAR GARNISH COVER LOWER LH

44. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

  1. B101642
    Connect the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B115750
    Attach the 2 claws to close the cover.

  1. B103254
    Connect the front seat outer belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


45. INSTALL FRONT DOOR OPENING TRIM RH

46. INSTALL FRONT DOOR OPENING TRIM LH

47. INSTALL FRONT DOOR SCUFF PLATE RH

48. INSTALL FRONT DOOR SCUFF PLATE LH

49. INSTALL REAR NO. 4 SEAT BELT ASSEMBLY OUTER

  1. B107675E01
    Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear No. 4 seat belt assembly outer.
      Text in Illustration 
      *a
      Unlocked
      *b
      Locked
      *c
      45°

  1. B107674
    Install the rear No. 4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107673
    Attach the 4 claws to install the retractor cover of the rear No. 4 seat belt assembly outer.

  1. B107672
    Connect the shoulder side of the rear No. 4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107671
    Attach the 2 claws to close the shoulder side cover of the rear No. 4 seat belt assembly outer.

  1. B107670
    Connect the floor side of the rear No. 4 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the rear No. 4 seat belt assembly outer installed.


    1. With the rear No. 4 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the rear No. 4 seat belt assembly outer.


50. INSTALL REAR NO. 3 SEAT BELT ASSEMBLY OUTER

  1. B107669E01
    Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear No. 3 seat belt assembly outer.
      Text in Illustration 
      *a
      Unlocked
      *b
      Locked
      *c
      45°

  1. B107668
    Install the rear No. 3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107667
    Attach the 4 claws to install the retractor cover of the rear No. 3 seat belt assembly outer.

  1. B107666
    Tighten the bolt to connect the shoulder side of the rear No. 3 seat belt assembly outer.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107665
    Attach the 4 claws to close the shoulder side cover of the rear No. 3 seat belt assembly outer.

  1. B107664
    Connect the floor side of the rear No. 3 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the rear No. 3 seat belt assembly outer installed.


    1. With the rear No. 3 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the rear No. 3 seat belt assembly outer.


51. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY OUTER

  1. B113927E01
    Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear No. 2 seat belt assembly outer.
      Text in Illustration 
      *a
      Unlocked
      *b
      Locked
      *c
      45°

  1. B105617
    Install the rear No. 2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B105616
    Connect the shoulder side of the rear No. 2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B105615
    Attach the 2 claws to close the shoulder side cover of the rear No. 2 seat belt assembly outer.

  1. B105614
    Connect the floor side of the rear No. 2 seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the rear No. 2 seat belt assembly outer installed.


    1. With the rear No. 2 seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the rear No. 2 seat belt assembly outer.


52. INSTALL REAR SEAT BELT ASSEMBLY OUTER

  1. B107663E01
    Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear seat belt assembly outer.
      Text in Illustration 
      *a
      Unlocked
      *b
      Locked
      *c
      45°

  1. B107662
    Tighten the bolt to install the rear seat belt assembly outer.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107661
    Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B107660
    Attach the 4 claws to close the shoulder side cover of the rear seat belt assembly outer.

  1. B107659
    Connect the floor side of the rear seat belt assembly outer with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. for Rear No. 1 Seat Bench Seat Type:

    1. B366455E01
      Check the degree of tilt when the ELR begins to lock.
      Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

      If operation is not as specified, replace the rear seat belt assembly outer.
      Text in Illustration 
      *a
      Unlocked
      *b
      Locked
      *c
      45°

    2. w/ Cover:

      1. Install the side trim cover to the rear seat belt assembly outer.
      2. Install the bolt to the floor side of the rear seat belt assembly outer.

    3. B357162
      Temporarily install the rear seat belt assembly outer with the 2 bolts.

    4. Tighten the lower side bolt first, and then tighten the upper side bolt to install the rear seat belt assembly outer.

      Torque:
      for Upper Bolt:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
      for Lower Bolt:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    5. Attach the 2 claws to install the retractor cover of the rear seat belt assembly outer.

    6. Tighten the bolt.

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    7. Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    8. Attach the 2 claws to close the shoulder side cover of the rear seat belt assembly outer.

    9. Tighten the bolt to connect the floor side of the rear seat belt assembly outer.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    10. w/ Cover:
      Attach the 3 guides and 3 claws to install the side trim cover.

  1. Check if the ELR locks.

    NOTICE:
    This check should be performed with the rear seat belt assembly outer installed.


    1. With the rear seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.
      If operation is not as specified, replace the rear seat belt assembly outer.


53. INSTALL REAR NO. 4 SEAT ASSEMBLY
Install the rear No. 4 seat assembly (Click here).

54. INSTALL REAR NO. 3 SEAT ASSEMBLY
  1. for Bench Type Seatback:
    Install the rear No. 3 seat assembly (Click here).

  1. for Separate Type Seatback:
    Install the rear No. 3 seat assembly (Click here).


55. INSTALL REAR NO. 2 SEAT ASSEMBLY
  1. w/ Headrest:
    Install the rear No. 2 seat assembly (Click here).

  1. w/o Headrest:
    Install the rear No. 2 seat assembly (See page (Click here).


56. INSTALL REAR NO. 1 SEAT ASSEMBLY
  1. for Fixed Seat Type:
    Install the rear No. 1 seat assembly (Click here).

  1. for Fold Down Seat Type:
    Install the rear No. 1 seat assembly (Click here).

  1. for Swiveling Seat Type:
    Install the rear No. 1 seat assembly (Click here).

  1. w/ Headrest:
    Install the rear No. 1 seat assembly (Click here).

  1. w/o Headrest:
    Install the rear No. 1 seat assembly (Click here)


57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Apr 2016 – Dec 2016)COMPONENTS (from Oct 2014) →