2014-2019 Hiace · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Oct 2014

A194498E46

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the STD Voltages column. The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbols)
Wiring Colors
Terminal Descriptions
Conditions
STD Voltages
B71-20 (BATT) - D97-105 (E1)
W - W-B
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B71-3 (+BM) - D97-105 (E1)
Y - W-B
Power source of throttle actuator
Always
11 to 14 V
B71-27 (IGSW) - D97-105 (E1)
B - W-B
Ignition switch
Ignition switch ON
11 to 14 V
B71-2 (+B) - D97-105 (E1)
L - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
B71-44 (MREL) - D97-105 (E1)
G - W-B
EFI relay
Ignition switch ON
11 to 14 V
D97-119 (VC) - D97-72 (E2)
L - Y
Power source of sensor
(specific voltage)
Ignition switch ON
4.5 to 5.0 V
D97-113 (VTA1) - D97-72 (E2)
R - Y
Throttle position sensor
(for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
3.3 to 4.9 V
D97-112 (VTA2) - D97-72 (E2)
G - Y
Throttle position sensor
(for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON, Accelerator pedal fully depressed
4.5 to 5.0 V
B71-55 (VPA) - B71-59 (EPA)
L - G
Accelerator pedal position sensor
(for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
B71-56 (VPA2) - B71-60 (EPA2)
B - GR
Accelerator pedal position sensor
(for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 4.75 V
B71-57 (VCPA) - B71-59 (EPA)
W - G
Power source of accelerator pedal position sensor
(for VPA)
Ignition switch ON
4.5 to 5.5 V
B71-58 (VCP2) - B71-60 (EPA2)
R - GR
Power source of accelerator pedal position sensor
(for VPA2)
Ignition switch ON
4.5 to 5.5 V
D97-69 (VG) - D97-92 (E2G)
Y-G - L
Mass air flow meter
Idling, Shift lever in neutral, A/C switch OFF
0.5 to 3.0 V
D97-87 (THA) - D97-72 (E2)
R - Y
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
D97-64 (THW) - D97-72 (E2)
R-W - Y
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
D97-66 (RTHW) - D97-72 (E2)
L - Y
Engine coolant temperature (radiator) sensor
Idling, radiator side engine coolant temperature -20 to 80°C (-4 to 176°F)
0.5 to 4.5 V
D97-86 (#10) - D97-46 (E01)
B - W-B
Fuel injector
Ignition switch ON
11 to 14 V
D97-85 (#20) - D97-46 (E01)
L - W-B
D97-84 (#30) - D97-46 (E01)
Y - W-B
Idling
Pulse generation
(see waveform 1)
D97-83 (#40) - D97-46 (E01)
R - W-B
D97-109 (IGT1) - D97-105 (E1)
R-L - W-B
Ignition coil with igniter
(ignition coil signal)
Idling
Pulse generation
(see waveform 2)
D97-108 (IGT2) - D97-105 (E1)
L-W - W-B
D97-107 (IGT3) - D97-105 (E1)
B-Y - W-B
D97-106 (IGT4) - D97-105 (E1)
Y-R - W-B
D97-82 (IGF1) - D97-105 (E1)
W-R - W-B
Ignition coil with igniter
(ignition confirmation signal)
Ignition switch ON
4.5 to 5.0 V
Idling
Pulse generation
(see waveform 2)
D97-94 (G2) - D97-118 (G2-)
Y - L
Camshaft position sensor
Idling
Pulse generation
(see waveform 3)
D97-93 (NE+) - D97-117 (NE-)
W - B
Crankshaft position sensor
Idling
Pulse generation
(see waveform 3)
B71-19 (FC) - D97-105 (E1)
L - W-B
Fuel pump control
Ignition switch ON
11 to 14 V
Idling
Below 1.5 V
D97-43 (M+) - D97-44 (ME01)
Y - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 4)
D97-42 (M-) - D97-44 (ME01)
L - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(see waveform 5)
D97-103 (A1A+) - D97-72 (E2)
B - Y
Heated oxygen sensor
Engine speed maintained 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(see waveform 6)
D97-104 (HA1A) - D97-81 (E03)
Y - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
D97-110 (KNK1) - D97-111 (EKNK)
G - R
Knock sensor
Maintain engine speed 4000 rpm after warming up
Pulse generation
(see waveform 7)
D97-74 (OC1+) - D97-96 (OC1-)
G - B
Camshaft timing oil control valve (OCV)
Idling
Pulse generation
(see waveform 8)
D97-62 (PRG) - D97-105 (E1)
B - W-B
EVAP VSV
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(see waveform 9)
B71-48 (STA) - D97-105 (E1)
R - W-B
Starter signal
Shift lever in neutral, ignition switch START
5.5 V or more
B71-36 (STP) - D97-105 (E1)
Y - W-B
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
B71-35 (ST1-) - D97-105 (E1)
R - W-B
Stop light switch
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
7.5 to 14 V
B71-31 (ELS) - D97-105 (E1)
G - W-B
Electric load
Taillight ON
7.5 to 14 V
Taillight OFF
0 to 1.5 V
B71-50 (ELS2) - D97-105 (E1)
B - W-B
Electric load
Defogger ON
7.5 to 14 V
Defogger OFF
0 to 1.5 V
B71-15 (TACH) - D97-105 (E1)
B - W-B
Engine speed
Idling
Pulse generation
(see waveform 10)
B71-38 (SPD) - D97-105 (E1)
P - W-B
Speed signal from combination meter
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 11)
B71-41 (TC) - D97-105 (E1)
G - W-B
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
B71-52 (PSW) - D97-105 (E1)
G - W-B
Power steering oil pressure switch
While turning steering wheel
Below 1.5 V
B71-46 (F/PS) - D97-105 (E1)
B - W-B
Airbag sensor assembly
Idling with warm engine
Pulse generation
(see waveform 12)
B71-8 (CANH) - D97-105 (E1)
B - W-B
Communication signal with other components
Ignition switch ON
Pulse generation
(see waveform 13)
B71-9 (CANL) - D97-105 (E1)
W - W-B
Communication signal with other components
Ignition switch ON
Pulse generation
(see waveform 14)
D97-80 (OX1B) - D97-72 (E2)
B - Y
Variable resistor
Ignition switch ON
0 to 5.5 V
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1

  1. A093279E03
    Fuel injector
    ECM Terminal Names
    Between #1 (to #4) and E01
    Tester Ranges
    20 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 2

  1. A093278E05
    Igniter IGT signal (from ECM to igniter)

  2. Igniter IGF signal (from igniter to ECM)

    ECM Terminal Names
    1. Between IGT (1 to 4) and E1
    2. Between IGF1 and E1
    Tester Ranges
    2 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 3

  1. A063955E01
    Camshaft position sensor

  2. Crankshaft position sensor

    ECM Terminal Names
    1. Between G2 and NE-
    2. Between NE+ and NE-
    Tester Ranges
    5 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 4

  1. A208000E06
    Throttle actuator positive terminal
    ECM Terminal Names
    Between M+ and ME01
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 5

  1. A245848E04
    Throttle actuator negative terminal
    ECM Terminal Names
    Between M- and ME01
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 6

  1. A093282E17
    Heated oxygen sensor
    ECM Terminal Names
    Between A1A+ and E2
    Tester Ranges
    0.2 V/DIV, 200 msec./DIV
    Conditions
    Engine speed maintained 2500 rpm for 2 minutes after warming up engine

    HINT:
    In the DATA LIST, item O2S B1S1 shows the ECM input values from the heated oxygen sensor.


WAVEFORM 7

  1. A283572E02
    Knock sensor
    ECM Terminal Names
    Between KNK1 and EKNK
    Tester Ranges
    1 V/DIV, 1 msec./DIV
    Conditions
    Engine speed maintained 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine rpm increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 8

  1. A093229E03
    Camshaft timing oil control valve (OCV)
    ECM Terminal Names
    Between OC1+ and OC1-
    Tester Ranges
    5 V/DIV, 1 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 9

  1. A205411E02
    EVAP VSV
    ECM Terminal Names
    Between PRG and E01
    Tester Ranges
    10 V/DIV, 20 msec./DIV
    Conditions
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 10

  1. A093225E02
    Engine speed signal
    ECM Terminal Names
    Between TACH and E1
    Tester Ranges
    5 V/DIV, 10 msec./DIV
    Conditions
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 11

  1. A093224E03
    Vehicle speed signal
    ECM Terminal Names
    Between SPD and E1
    Tester Ranges
    5 V/DIV, 20 msec./DIV
    Conditions
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 12

  1. A093227E01
    Airbag sensor assembly
    ECM Terminal Names
    Between F/PS and E1
    Tester Ranges
    5 V/DIV, 500 msec./DIV
    Conditions
    Idling with warm engine


WAVEFORM 13

  1. A086154E02
    CAN communication signal
    ECM Terminal Names
    Between CANH and E1
    Tester Ranges
    1 V/DIV, 10 μs/DIV
    Conditions
    Ignition switch ON


WAVEFORM 14

  1. A086155E02
    CAN communication signal
    ECM Terminal Names
    Between CANL and E1
    Tester Ranges
    1 V/DIV, 10 μs/DIV
    Conditions
    Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Jan 2017)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →