2014-2019 Hiace · Service Manual ENGINE

Variable Resistor Circuit

Circuit diagnosis · Vehicles built from Oct 2014

DESCRIPTION

The variable resistor is used to adjust the concentration of CO in the exhaust during idling. By turning the idle mixture adjusting screw located on the variable resistor clockwise, the contact inside the resistor is moved and the voltage at the VAF terminal rises accordingly. Conversely, turning the adjusting screw counterclockwise reduces the VAF terminal voltage. When the VAF terminal voltage rises, the ECM increases the fuel injection volume slightly, thus making the air-fuel ratio slightly richer.

WIRING DIAGRAM

A204543E01

INSPECTION PROCEDURE

NOTICE:
Always use a CO meter when adjusting the concentration of CO during idling. If a CO meter is not available, do not attempt to adjust the idling CO concentration.


1. CHECK CO/HC
  1. Make sure the following conditions are met:

    1. All the vacuum lines are properly connected.

    2. The CO meter is properly calibrated.

  1. Start the engine.

  1. Make sure the following conditions are met:

    1. The parking brake is securely applied.

    2. The shift lever is in neutral.

    3. All the accessories are switched off.

  1. Warm up the engine and check that the idling speed is appropriate.

  1. Race the engine at 2500 rpm for approximately 2 minutes.

  1. Insert a tester probe at least 40 cm (1.3 ft.) into the tailpipe.

  1. Measure the CO concentration 1 to 3 minutes after racing the engine to allow the concentration to stabilize.

Standard CO concentration rate at idling:
1.0 to 2.0%

HINT:
If the result is outside the standard range shown above, maintain the measurement conditions established during this procedure. The measurement conditions are used in the CO concentration adjustment procedure described below.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. ADJUST CO CONCENTRATION

  1. A208794E01
    Make sure that all the conditions established in the previous procedure remain unchanged.

  1. Regulate the idling CO concentration so that it is within 1.0 to 2.0%.

    HINT:
    Use SST and the idle mixture adjusting screw located on the variable resistor. By turning the adjusting screw, the idling CO concentration rate can be regulated.

    Reference 
    Result
    Proceed To
    Unable to obtain standard concentration rate
    A
    Standard concentration rate obtained
    B

SST
09243-00020  


B
ADJUSTMENT COMPLETE
A


3. INSPECT VARIABLE RESISTOR

  1. A107931E02
    Remove the variable resistor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E2) - 2 (VC)
    Always
    3.5 to 6.5 kΩ

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E2) - 3 (VAF)
    Adjusting screw turned fully clockwise
    3.5 to 6.5 kΩ
    Adjusting screw turned fully counterclockwise
    0 kΩ

SST
09243-00020  

HINT:
When the adjusting screw is turned fully clockwise, the resistance is the same as the measurement value between terminals 1 and 2. When the adjusting screw is turned fully counterclockwise, the resistance changes to 0 kΩ.



NG
REPLACE VARIABLE RESISTOR
OK


4. CHECK HARNESS AND CONNECTOR (VARIABLE RESISTOR - ECM)
  1. Disconnect the variable resistor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D31-2 (VC) - D97-119 (VC)
    Always
    Below 1 Ω
    D31-3 (VAF) - D97-80 (OX1B)
    Always
    Below 1 Ω
    D31-1 (E2) - D97-72 (E2)
    Always
    Below 1 Ω
    D31-2 (VC) or D97-119 (VC) - Body ground
    Always
    10 kΩ or higher
    D31-3 (VAF) or D97-80 (OX1B) - Body ground
    Always
    10 kΩ or higher
    D31-1 (E2) or D97-72 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT ECM (VC VOLTAGE)

  1. A204541E02
    Disconnect the variable resistor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D31-2 (VC) - D31-1 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Variable Resistor)



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← Starter Signal Circuit (from Jan 2017)Brake Override System (Oct 2014 – Dec 2014) →