P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.- HINT:
- The normal signal conditions are as shown in the table below.
Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
- [OFF] denotes ground potential.
- [ON] denotes battery potential (+B).
- On the intelligent tester, the Data List items Stop Light Switch and ST1 are both ON when the brake pedal is depressed because the characteristics of ST1 indication are the opposite of the characteristics of Stop Light Switch indication.
- [OFF] denotes ground potential.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0504 |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch is ON. (b) Brake pedal is released. (c) STP signal is OFF when the ST1- signal is OFF. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Stop light switch conditions can be checked using the intelligent tester.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the intelligent tester on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.
- Check the Data List indication when the brake pedal is depressed and released.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| Brake Pedal Operation |
Stop Light Switch |
ST1 |
| Depressed |
ON |
ON |
| Released |
OFF |
OFF |
| 1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.
Read the value displayed on the intelligent tester.
- Standard:
Condition
Specified Condition
Brake pedal depressed
STP signal ON
Brake pedal released
STP signal OFF
|
|
||||
| OK | ||
| ||
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE) |
![]() ![]() |
Disconnect the stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B2-2 - Body ground
Always
11 to 14 V
B2-4 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Switch Assembly)
|
|
||||
| OK | |
| 3. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Inspect the stop light switch assembly (Click here).
|
|
||||
| OK | |
| 4. INSPECT ECM (STP AND ST1- VOLTAGE) |
![]() ![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B71-35 (ST1-) - Body ground
Brake pedal released
7.5 to 14 V
Brake pedal depressed
Below 1.5 V
B71-36 (STP) - Body ground
Brake pedal released
Below 1.5 V
Brake pedal depressed
7.5 to 14 V
Text in Illustration *a
Depressed
*b
Released
*c
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||


