P0504 Brake Switch "A" / "B" Correlation
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.- HINT:
- The normal signal conditions are as shown in the table below.
Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Depress and release brake pedal with ignition switch to ON |
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch to ON. (b) Brake pedal is released. (c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on. |
|
| DTC No. |
Data List |
| P0504 |
Stop Light Switch |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE) |
Disconnect the stop light switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B2-2 - Body ground
Always
11 to 14 V
B2-4 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Stop Light Switch)
Reconnect the stop light switch connector.
|
|
||||
| OK | |
| 2. INSPECT STOP LIGHT SWITCH ASSEMBLY |
Inspect the stop light switch assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK ECM (STP AND ST1- VOLTAGE) |
![]() ![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Brake Pedal Condition
Specified Condition
B88-34 (ST1-) - Body ground
Released
11 to 14 V
Depressed
0 to 1.5 V
B88-35 (STP) - Body ground
Released
0 to 1.5 V
Depressed
11 to 14 V
Text in Illustration *a
Brake Pedal Depressed
*b
Brake Pedal Released
*c
Front view of wire harness connector
(to ECM)
Reconnect the ECM connector.
|
|
||||
|
|
||||
| 4. REPLACE STOP LIGHT SWITCH ASSEMBLY |
Replace the stop light switch assembly.
|
|
||||
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the GTS on.
Depress and release the brake pedal.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||

