2014-2019 Hiace · Service Manual BRAKE

C1241/41 Low Battery Positive Voltage

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

If there is a problem with the brake actuator assembly (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits the ABS operation with the fail safe function.
If the voltage supplied to the IG1 terminal is not within the DTC detection threshold due to malfunctions in such as the battery and alternator circuit, this DTC is stored.
DTC No.
DTC Detection Condition
Trouble Area
C1241/41
When any of the following is detected:
  1. Vehicle speed is 1.8 mph (3 km/h) or more and IG1 terminal voltage is 9.5 V or less for at least 10 seconds.
  1. While the solenoid relay is ON, the IG1 terminal voltage is 9.5 V or less and the relay contact is open for at least 0.2 seconds.
  1. While the motor relay is ON, the IG1 terminal voltage is 9.5 V or less and the relay contact is open for at least 0.2 seconds.
  1. Battery
  1. ECU-IG NO. 1 fuse
  1. Charging system
  1. Power source circuit

WIRING DIAGRAM

C302240E01

INSPECTION PROCEDURE

HINT:
After steps 1 and 2 are completed, start the inspection from step 3 when using the intelligent tester, and from step 4 when not using the intelligent tester.


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM
OK


2. INSPECT FUSE (ECU-IG NO. 1 FUSE)
C111269E02
  1. Remove the ECU-IG NO. 1 fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    ECU-IG NO. 1 (7.5 A) fuse
    Below 1 Ω (Continuity)



NG
REPLACE FUSE (ECU-IG NO.1 FUSE)
OK


3. READ VALUE USING INTELLIGENT TESTER (IG1 POWER SUPPLY)
  1. Install the ECU-IG NO. 1 fuse.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Start the engine.

  1. Select the DATA LIST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    ECU IG Power Voltage
    ECU IG power supply voltage / TOO LOW/NORMAL
    TOO LOW: 9.5 V or less
    NORMAL: 9.5 to 14.0 V
    -

  1. Measure the voltage output from the ECU displayed on the intelligent tester.

    OK:
    "Normal" is displayed.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


4. INSPECT SKID CONTROL ECU (IG1 TERMINAL VOLTAGE)

  1. C058919E14
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    B19-25 (IG1) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)

  1. C058919E11
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    B19-2 (GND1) - Body ground
    Below 1 Ω
    B19-24 (GND2) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check that the same DTC is recorded (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Condition
    Proceed to
    DTC (C1241/41) is output
    A
    DTC (C1241/41) is not output (When troubleshooting in accordance with the DTC CHART)
    B
    DTC (C1241/41) is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
    C



B
END

C
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C0278/11 Open in ABS Solenoid Relay Circuit (+ C0279/12) (from Jan 2017)C1241/41 Low Battery Positive Voltage (Jan 2015 – Dec 2016) →