C1241/41 Low Battery Positive Voltage
Diagnostic trouble codes · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
If there is a problem with the brake actuator assembly (skid control ECU) power supply circuit, the skid control ECU outputs the DTC and prohibits the ABS operation with the fail safe function.If the voltage supplied to the IG1 terminal is not within the DTC detection threshold due to malfunctions in such as the battery and alternator circuit, this DTC is stored.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1241/41 |
When any of the following is detected:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- After steps 1 and 2 are completed, start the inspection from step 3 when using the intelligent tester, and from step 4 when not using the intelligent tester.
| 1. INSPECT BATTERY |
Check the battery voltage.
- Standard voltage:
- 11 to 14 V
|
|
||||
| OK | |
| 2. INSPECT FUSE (ECU-IG NO. 1 FUSE) |
![]() ![]() |
Remove the ECU-IG NO. 1 fuse from the instrument panel junction block.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
ECU-IG NO. 1 (7.5 A) fuse
Below 1 Ω (Continuity)
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (IG1 POWER SUPPLY) |
Install the ECU-IG NO. 1 fuse.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester main switch on.
Start the engine.
Select the DATA LIST mode on the intelligent tester.
ABS: Item (Display)
Measurement Item / Range (Display)
Normal Condition
Diagnostic Note
ECU IG Power Voltage
ECU IG power supply voltage / TOO LOW/NORMAL
TOO LOW: 9.5 V or less
NORMAL: 9.5 to 14.0 V
-
Measure the voltage output from the ECU displayed on the intelligent tester.
- OK:
- "Normal" is displayed.
|
|
||||
| OK | |
| 4. INSPECT SKID CONTROL ECU (IG1 TERMINAL VOLTAGE) |
Disconnect the skid control ECU connector.

Turn the ignition switch to ON position.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Specified Condition
B19-25 (IG1) - Body ground
10 to 14 V
|
|
||||
| OK | |
| 5. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY) |
Turn the ignition switch off.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
B19-2 (GND) - Body ground
Below 1 Ω
B19-24 (GND) - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Check that the same DTC is recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTC (C1241/41) is output
A
DTC (C1241/41) is not output (When troubleshooting in accordance with the DTC CHART)
B
DTC (C1241/41) is not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
C
|
|
||||
|
|
||||
| A | ||
| ||

