2014-2019 Hiace · Service Manual ENGINE

B2282 Vehicle Speed Signal Malfunction

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2282
The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
  1. AM2 fuse
  2. Meter/gauge system
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.
B2283
Either of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
  1. Vehicle speed signal malfunction detection 1: Excessive deceleration is detected
  2. Vehicle speed signal malfunction detection 2: Engine speed linked detection
  1. AM2 fuse
  2. Meter/gauge system
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Run the engine at an engine speed of 2000 rpm or more for 330 seconds.
  1. *: Only detected while a malfunction is present and the engine switch is on (IG)
Vehicle Condition and Fail-safe Function when Malfunction Detected 
DTC Code
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
B2282
  1. When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.
  2. When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be turned from on (IG) to off.
-
B2283
  1. The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.
  2. With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start.
Steering lock operation is prohibited.
Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2282
B2283
Power Source Control
  1. Vehicle Speed Signal
  2. Engine Condition
  3. Power Supply Condition
Starting Control
  1. Engine Speed
Combination Meter
  1. Vehicle Speed Meter
-

WIRING DIAGRAM

C299865E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. READ VALUE USING GTS (VEHICLE SPEED METER)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Read the Data List according to the display on the GTS.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed (Speedometer tester)
    -

    OK:
    Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO METER / GAUGE SYSTEM (Speedometer Malfunction) (Click here)
OK


2. READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List according to the display on the GTS.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Signal
    Vehicle being driven or stopped/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -

    OK:
    Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.



NG
Go to step 3
OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

3. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.C299853E01

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B75-1 (+B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4. CHECK HARNESS AND CONNECTOR (GROUND)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.C299853E02

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-10 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the H20 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-7 (SPD) - H20-6 (+S)
    Always
    Below 1 Ω
    B75-7 (SPD) or H20-6 (+S) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.C300092E01

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

  1. Reconnect the H20 combination meter assembly connector.

  1. Connect an oscilloscope to terminal B75-7 (SPD) and B75-10 (E).

  1. Turn the engine switch on (IG).

  1. Check the signal waveform according to the condition(s) in the table below.

    Item
    Condition
    Tester Connection
    B75-7 (SPD) - B75-10 (E)
    Tool setting
    5 V/DIV., 20 ms./DIV.
    Vehicle condition
    Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

    OK:
    The waveform is similar to that shown in the illustration.

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


← B2282 Vehicle Speed Signal Malfunction (+ B2283) (Jan 2015 – Mar 2016)B2282 Vehicle Speed Signal Malfunction (+ B2283) (Jan 2017 – Nov 2017) →