B2282 Vehicle Speed Signal Malfunction
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Also covers:
- B2283 Vehicle Speed Sensor Malfunction
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.
- HINT:
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2282 |
The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match. |
|
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds. |
| B2283 |
Either of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
|
|
Run the engine at an engine speed of 2000 rpm or more for 330 seconds. |
- *: Only detected while a malfunction is present and the engine switch is on (IG)
| DTC Code |
Vehicle Condition when Malfunction Detected |
Fail-safe Function when Malfunction Detected |
| B2282 |
|
- |
| B2283 |
|
Steering lock operation is prohibited. |
| DTC |
Data List Item |
Active Test Item |
| B2282 B2283 |
Power Source Control
Starting Control
Combination Meter
|
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
- Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. READ VALUE USING GTS (VEHICLE SPEED METER) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
Combination Meter Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed Meter
Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Almost same as actual vehicle speed (Speedometer tester)
-
- OK:
- Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 2. READ VALUE USING GTS (VEHICLE SPEED SIGNAL) |
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed Signal
Vehicle being driven or stopped/Stop or Run
Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
- OK:
- Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-1 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (GROUND) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-10 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the H20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-7 (SPD) - H20-6 (+S)
Always
Below 1 Ω
B75-7 (SPD) or H20-6 (+S) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the B75 certification ECU (smart key ECU assembly) connector.


Text in Illustration *a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
Reconnect the H20 combination meter assembly connector.
Connect an oscilloscope to terminal B75-7 (SPD) and B75-10 (E).
Turn the engine switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
Item
Condition
Tester Connection
B75-7 (SPD) - B75-10 (E)
Tool setting
5 V/DIV., 20 ms./DIV.
Vehicle condition
Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)
- OK:
- The waveform is similar to that shown in the illustration.
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
|
|
||||
| OK | ||
| ||
