B2284 Brake Signal Malfunction
Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.- HINT:
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2284 |
The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match. |
|
Connect the cable to the negative (-) battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more. |
- *: Only detected while a malfunction is present and the engine switch is on (IG)
| Vehicle Condition when Malfunction Detected |
Fail-safe Function when Malfunction Detected |
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the indicator in the combination meter is not illuminated in green). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
|
- |
| DTC |
Data List Item |
Active Test Item |
| B2284 |
Power Source Control
ABS/VSC/TRC
|
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Check the connector connection to the terminal to make sure that there is no abnormality such as a loose connection, deformation, etc.
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
- Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the smart entry and start system (for Start Function) precaution (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. READ VALUE USING GTS (STOP LIGHT SWITCH 1) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Specified Condition
Stop Light Switch1
State of brake pedal/ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
- Use this item to determine whether the stop light switch is malfunctioning.
- The engine cannot be started when this item is OFF.
- When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
- OK:
- ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.
- Use this item to determine whether the stop light switch is malfunctioning.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-1 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GROUND) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-10 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the B2 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B2-2 - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-11 (STP1) - B2-1
Always
Below 1 Ω
B75-11 (STP1) or B2-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the B75 certification ECU (smart key ECU assembly) connector.
Reconnect the B2 stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-11 (STP1) - Body ground
Brake pedal released
1 V or less
Brake pedal depressed
9 V or higher
|
|
||||
| OK | ||
| ||
