C1434 Steering Angle Sensor Output Malfunction
Diagnostic trouble codes · Vehicles built Jan 2017 – Nov 2017
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.- HINT:
- When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
- Steering angle sensor zero point malfunction
- Steering angle sensor signal malfunction
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1434 |
Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point. |
|
WIRING DIAGRAM
Refer to DTC C1432 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Do not remove the steering angle sensor from the spiral with sensor cable subassembly.
- When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.
- Do not remove the steering angle sensor from the spiral with sensor cable subassembly.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click here).
- When any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable subassembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).
- When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click here).
| 1. CHECK DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch ON again and check that no CAN communication system DTC is output (Click here).
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output (Click here).
- Result:
Result
Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output
A
CAN communication system DTC is output
B
Speed sensor or yaw rate and acceleration sensor DTC is output
C
- HINT:
- If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.
- If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral with sensor cable sub-assembly).
- If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) sensor is normal.
|
|
||||
|
|
||||
| A | |
| 2. CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL) |
Turn the ignition switch off.
Remove the steering wheel and the column cover.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the H92 steering angle sensor (spiral with sensor cable sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
H92-5 (BAT) - Body ground
Always
11 to 14 V
H92-4 (IG) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (ESS TERMINAL) |
Turn the ignition switch off.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H92-1 (ESS) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))
- HINT:
- If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
