2014-2019 Hiace · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH

  1. B111204E03
    Inspect the door closer motor.

    1. Apply battery voltage and check operation of the slide door closer motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Close (Forward)
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Open (Reverse)

  1. B111205E03
    Inspect the pawl switch and latch switch

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      Pawl switch:
      Tester Connection
      Condition
      Specified Condition
      8 - 9
      1. Open
      1. Half latch
      1. Full latch
      10 kΩ or higher
      8 - 9
      Unlatched
      Below 1 Ω
      Latch switch:
      Tester Connection
      Condition
      Specified Condition
      3 - 4, 4- 8
      Open
      Below 1 Ω
      4 - 8
      Half latch
      Below 1 Ω
      3 - 4, 4- 8
      Full latch
      10 kΩ or higher
      -
      Over stroke
      10 kΩ or higher

  1. B111206E02
    Inspect the initial position switch and handle switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      8 - 10
      1. Handle switch ON (Handle initial position)
      1. Initial position switch OFF (Active lever initial position)
      10 kΩ or higher
      8 - 10
      1. Handle switch OFF (As handling)
      1. Initial position switch OFF (Active lever initial position)
      10 kΩ or higher
      8 - 10
      1. Handle switch ON (Handle initial position)
      1. Initial position switch ON (As closer operating)
      Below 1 Ω
      8 - 10
      1. Handle switch OFF (As handling)
      1. Initial position switch ON (As closer operating)
      10 kΩ or higher


INSPECT POWER SLIDE DOOR LOCK ASSEMBLY LH

  1. B111198E02
    Inspect the door closer motor.

    1. Apply battery voltage and check operation of the slide door closer motor.

      Standard:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Close (Forward)
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Open (Reverse)

  1. B111199E02
    Inspect the pawl switch and latch switch

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      Pawl switch:
      Tester Connection
      Condition
      Specified Condition
      8 - 9
      1. Open
      1. Half latch
      1. Full latch
      10 kΩ or higher
      8 - 9
      Unlatched
      Below 1 Ω
      Latch switch:
      Tester Connection
      Condition
      Specified Condition
      3 - 4, 4- 8
      Open
      Below 1 Ω
      4 - 8
      Half latch
      Below 1 Ω
      3 - 4, 4- 8
      Full latch
      10 kΩ or higher
      -
      Over stroke
      10 kΩ or higher

  1. B111203E02
    Inspect the initial position switch and handle switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      8 - 10
      1. Handle switch ON (Handle initial position)
      1. Initial position switch OFF (Active lever initial position)
      10 kΩ or higher
      8 - 10
      1. Handle switch OFF (As handling)
      1. Initial position switch OFF (Active lever initial position)
      10 kΩ or higher
      8 - 10
      1. Handle switch ON (Handle initial position)
      1. Initial position switch ON (As closer operating)
      Below 1 Ω
      8 - 10
      1. Handle switch OFF (As handling)
      1. Initial position switch ON (As closer operating)
      10 kΩ or higher

← REASSEMBLY (from Jan 2017)COMPONENTS (from Oct 2014) →