Driver Side Door Entry Lock and Unlock Functions do not Operate
Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the driver door or the front door outside handle assembly RH (trigger switch) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and front door outside handle assembly RH [driver door electrical key antenna]), or there may be wave interference.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN).
While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Check that there are no electrical key transmitter sub-assemblies in the vehicle.
- Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
- After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
- The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK POWER DOOR LOCK CONTROL SYSTEM |
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. CHECK FOR DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC B27A1 is not output.
A
DTC B27A1 is output.
B
|
|
||||
| A | |
| 3. CHECK WAVE ENVIRONMENT |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly RH and perform an entry function check (Click here).

Text in Illustration *a
Approximately 0.3 m (0.984 ft.)
- NOTICE:
- If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
- HINT:
- If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
Result Result
Proceed to
Entry function does not operate normally.
A
Entry function operates normally.
B
|
|
||||
| A | |
| 4. READ VALUE USING GTS (D-DOOR TRIGGER SWITCH) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
Entry&Start Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
D-Door Trigger Switch
Driver door trigger switch / ON or OFF
ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed
- Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).
- Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.
- OK:
- On the GTS screen, the display changes between ON and OFF as shown in the table above.
- Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).
|
|
||||
| OK | |
| 5. CHECK KEY DIAGNOSTIC MODE |
Check the following antennas in key diagnostic mode.

Text in Illustration *a
0.7 to 1 m (2.30 to 3.28 ft.)
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
- HINT:
- If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the No. 1 indoor electrical key antenna assembly (front bumper RH):When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly RH, check that the wireless door lock buzzer sounds.
- OK:
- Wireless door lock buzzer sounds.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU] - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY) |
Disconnect the B76 certification ECU (smart key ECU assembly) connector.
Disconnect the A40 No.1 indoor electrical key antenna assembly (front bumper RH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B76-31 (CLG1) - A40-1 (ANTE1)
Always
Below 1 Ω
B76-30 (CG1B) - A40-2 (CLGB)
Always
Below 1 Ω
B76-31 (CLG1) or A40-1 (ANTE1) - Body ground
Always
10 kΩ or higher
B76-30 (CG1B) or A40-2 (CLGB) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY) |
Connect the A40 No. 1 indoor electrical key antenna assembly (front bumper RH) connector.
Connect the B76 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.


Text in Illustration *a
Component with harness connected
(Certification ECU [Smart Key ECU Assembly])
*b
Waveform 1
*c
Trigger switch ON
-
-
- OK:
Tester Connection
Switch Condition
Tool Setting
Specified Condition
B76-31 (CLG1) - B76-30 (CG1B)
Procedure: - Engine switch off
- All doors closed
-
Not pulse generation
Procedure: - Engine switch off
- All doors closed
- Press the trigger switch on the front door outside handle assembly RH
2 V/DIV., 500 ms/DIV.
Pulse generation (See waveform 1)
- Engine switch off
|
|
||||
| OK | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH AND BODY GROUND) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the K8 front door outside handle assembly RH (trigger switch) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-4 (TSW1) - K8-1
Always
Below 1 Ω
K8-2 - Body ground
Always
Below 1 Ω
B75-4 (TSW1) or K8-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH (TRIGGER SWITCH) |
Remove the front door outside handle assembly RH (trigger switch) (Click here).
Inspect the front door outside handle assembly RH (trigger switch) (Click here).
|
|
||||
| OK | |
| 10. CHECK ENTRY DOOR LOCK OPERATION |
Check the operation of the entry lock/unlock function.
- HINT:
- Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly RH before performing the inspection.
- OK:
- Entry lock/unlock operate normally.
|
|
||||
| OK | ||
| ||
