Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)
Engine does not Start because No Initial Combustion
Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.
If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.
When using the GTS with the engine switch off to troubleshoot: When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
1. CLEAR DTC
Clear the DTCs (Click here ).
NEXT
2. CHECK FOR DTC
Check for DTCs (Click here ).
HINT:
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
Result
Result
Proceed to
DTCs are not output
A
DTCs are output
B
B
A
3. READ VALUE USING GTS (IMMOBILISER FUEL CUT)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
Tester Display
Measurement Item / Range
Normal Condition
Diagnostic Note
Immobiliser Fuel Cut
Status of immobiliser system fuel cut / OFF/ON
ON: Immobiliser fuel cut on OFF: Immobiliser fuel cut off
-
OK:
The item in the Data List indicates "OFF".
Result
Result
Proceed to
OK (for 1TR-FE, 2TR-FE)
A
OK (for 1KD-FTV, 2KD-FTV)
B
NG
C
HINT:
*: Go to procedure:
for 1TR-FE (w/ Dual VVT-i): Click here
for 2TR-FE (w/ Secondary Air Injection System): Click here
for 2TR-FE (w/o Secondary Air Injection System): Click here
for 2TR-FE (w/ Dual VVT-i): Click here
for 1KD-FTV (w/ DPF): Click here
for 1KD-FTV (w/o DPF): Click here
for 2KD-FTV: Click here
B
C
A
4. CHECK SECURITY INDICATOR LIGHT OPERATION
Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.
OK:
Security indicator light turns off.
NG
OK
GO TO ENGINE DOES NOT START BUT INITIAL COMBUSTION OCCURS (Click here )
5. CHECK SECURITY INDICATOR LIGHT OPERATION
Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.
OK:
Security indicator light turns off.
NG
OK
6. CHECK WHETHER ENGINE STARTS
Using another registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
Result
Result
Proceed to
Engine can be started
A
Engine cannot be started
B
B
GO TO ENGINE DOES NOT START BUT INITIAL COMBUSTION OCCURS (Click here )
A
7. REPLACE KEY
Replace the key.
NOTICE:
Key ID code registration is necessary when replacing the key.
Refer to Service Bulletin.
NEXT
8. CHECK WHETHER ENGINE STARTS
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
Result
Result
Proceed to
Engine can be started
A
Engine cannot be started (for 1TR-FE, 2TR-FE)
B
Engine cannot be started (for 1KD-FTV, 2KD-FTV)
C
HINT:
*: Go to procedure:
for 1TR-FE (w/ Dual VVT-i): Click here
for 2TR-FE (w/ Secondary Air Injection System): Click here
for 2TR-FE (w/o Secondary Air Injection System): Click here
for 2TR-FE (w/ Dual VVT-i): Click here
for 1KD-FTV (w/ DPF): Click here
for 1KD-FTV (w/o DPF): Click here
for 2KD-FTV: Click here
B
C
A
9. REPLACE TRANSPONDER KEY COIL
Temporarily replace the transponder key coil with a new or known good one (Click here ).
NEXT
10. CHECK WHETHER ENGINE STARTS
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
Result
Result
Proceed to
Engine can be started
A
Engine cannot be started
B
B
A
END (TRANSPONDER KEY COIL WAS DEFECTIVE)
11. REPLACE TRANSPONDER KEY ECU ASSEMBLY
Replace the transponder key ECU assembly with a new one.
HINT:
Refer to Service Bulletin.
NOTICE:
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to Service Bulletin.
NEXT
12. CHECK WHETHER ENGINE STARTS
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
Result
Result
Proceed to
Engine can be started
A
Engine cannot be started
B
B
A
END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)
13. REPLACE KEY
Temporarily replace the key with a new or known good one.
NOTICE:
Key ID code registration is necessary when replacing the key.
Refer to Service Bulletin.
NEXT
14. CHECK WHETHER ENGINE STARTS
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
OK:
Engine starts normally.
Result
Result
Proceed to
Engine can be started
A
Engine cannot be started (for 1TR-FE, 2TR-FE)
B
Engine cannot be started (for 1KD-FTV, 2KD-FTV)
C
HINT:
*: Go to procedure:
for 1TR-FE (w/ Dual VVT-i): Click here
for 2TR-FE (w/ Secondary Air Injection System): Click here
for 2TR-FE (w/o Secondary Air Injection System): Click here
for 2TR-FE (w/ Dual VVT-i): Click here
for 1KD-FTV (w/ DPF): Click here
for 1KD-FTV (w/o DPF): Click here
for 2KD-FTV: Click here
B
C
A