P1120 Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit
Diagnostic trouble codes · Vehicles built from Jan 2015
Versions by build date: Oct 2014 – Dec 2014 from Jan 2015
DESCRIPTION
- HINT:
- This is the repair procedure for the accelerator pedal position sensor.
- The electrical throttle system does not use a throttle cable.
- The accelerator pedal position sensor is a non-contact type.
- This is the repair procedure for the accelerator pedal position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V, in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting a malfunction. The ECM judges the current opening angle of the accelerator pedal from these signals input from terminals VPA and VPA2, and the ECM controls the injection pump based on these signals.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1120 |
Condition (a), (b), (c) or (d) continues for 2.0 seconds: (a) VPA is 0.2 V or less and VPA2 is 0.5 V or less. (b) VPA is 4.8 V or higher. (c) VPA2 is 4.8 V or higher, and VPA is between 0.4 V and 3.45 V. (d) The difference between VPA and VPA2 is 0.02 V or less. |
|
| Condition (a) continues for 0.5 seconds: (a) VPA is 0.2 V or less or VPA2 is 0.5 V or less. |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING GTS (ACCELERATOR POSITION) |
Connect the GTS to the DLC3.

Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
- OK:
- Check that the value displayed on the GTS changes by repeatedly depressing and releasing the accelerator pedal.
|
|
||||
| OK | |
| 2. READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
- Result:
Display (DTC output)
Proceed to
DTC P1120 is output again
A
No DTC output
B
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
B1-1 (VCP2) - B74-57 (VCP2)
Always
Below 1 Ω
B1-2 (EPA2) - B74-56 (EPA2)
Always
Below 1 Ω
B1-3 (VPA2) - B74-55 (VPA2)
Always
Below 1 Ω
B1-4 (VCPA) - B74-58 (VCPA)
Always
Below 1 Ω
B1-5 (EPA) - B74-59 (EPA)
Always
Below 1 Ω
B1-6 (VPA) - B74-60 (VPA)
Always
Below 1 Ω
B1-1 (VCP2) or B74-57 (VCP2) - Body ground
Always
10 kΩ or higher
B1-2 (EPA2) or B74-56 (EPA2) - Body ground
Always
10 kΩ or higher
B1-3 (VPA2) or B74-55 (VPA2) - Body ground
Always
10 kΩ or higher
B1-4 (VCPA) or B74-58 (VCPA) - Body ground
Always
10 kΩ or higher
B1-5 (EPA) or B74-59 (EPA) - Body ground
Always
10 kΩ or higher
B1-6 (VPA) or B74-60 (VPA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
Disconnect the accelerator pedal position sensor connector.

Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B1-1 (VCP2) - B1-2 (EPA2)
Ignition switch ON
4.5 to 5.5 V
B1-4 (VCPA) - B1-5 (EPA)
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Accelerator Pedal Position Sensor)
|
|
||||
| OK | |
| 5. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 6. READ OUTPUT DTC (ACCELERATOR PEDAL POSITION SENSOR DTC IS OUTPUT AGAIN) |
Clear the DTC (Click here).
Start the engine.
Idle the engine for 15 seconds or more.
Read the DTC (Click here).
- Result:
Display (DTC output)
Proceed to
DTC P1120 is output again
A
No DTC output
B
|
|
||||
| A | ||
| ||
