2014-2019 Hiace · Service Manual BODY ELECTRICAL

ON-VEHICLE INSPECTION

Inspection · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


INSTALL INDICATOR/WARNING LIGHT
  1. Check the following indicators and warning lights.

    Indicator/Warning Light
    Switch Condition
    Switch Condition
    ABS warning light
    Ignition switch off → ON
    Comes on for 3 seconds
    BRAKE warning light
    T-BELT warning light*1
    Eco driving indicator light*2
    Headlight beam level control system indicator light*3, *4
    DPF indicator light*5
    Brake override system warning light
    LED headlight warning light*3, *4
    AIRBAG warning light*6
    Ignition switch off → ON
    Comes on for 6 seconds
    CHECK E/G warning light
    Ignition switch off → ON
    1. Illuminates when ignition switch turned ON
    2. Turns off when engine started
    CHARGE warning light
    OIL warning light
    1. *1: Engine Type Diesel
    2. *2: for Automatic Transmission
    3. *3: for LED Headlight
    4. *4: for Segment Display Type
    5. *5: for 1KD-FTV (w/ DPF)
    6. *6: w/ Airbag System


INSPECT SPEEDOMETER
  1. Using a speedometer tester, check the speedometer indication according to the table below.

    for mph 
    Standard Indication
    Acceptable Range
    20
    21.0 to 23.5
    40
    42.0 to 44.5
    60
    62.5 to 66.0
    80
    83.1 to 87.1
    100
    103.9 to 108.4
    for km/h (except Australia) 
    Standard Indication
    Acceptable Range
    20
    21.0 to 25.0
    40
    41.7 to 46.2
    60
    62.7 to 67.2
    80
    83.4 to 88.4
    100
    104.3 to 109.3
    120
    125.1 to 130.6
    140
    145.8 to 151.8
    160
    166.2 to 173.2
    for km/h (except 1KD-FTV, Manual Transmission [for Australia]) 
    Standard Indication
    Acceptable Range
    20
    20.4 to 24.4
    40
    41.0 to 45.5
    60
    61.4 to 65.9
    80
    82.0 to 87.0
    100
    10.24 to 107.4
    120
    122.8 to 128.3
    140
    143.4 to 149.4
    160
    163.8 to 170.3
    for km/h (for 1KD-FTV, Manual Transmission [for Australia]) 
    Standard Indication
    Acceptable Range
    20
    20.6 to 24.6
    40
    41.3 to 45.8
    60
    61.9 to 66.4
    80
    82.6 to 87.6
    100
    103.2 to 107.7
    120
    123.9 to 128.9
    140
    144.5 to 149.5
    160
    165.2 to 170.2
    for km/h (for Automatic Transmission [for Australia]) 
    Standard Indication
    Acceptable Range
    20
    20.1 to 24.1
    40
    40.2 to 44.7
    60
    60.4 to 64.9
    80
    80.5 to 85.5
    100
    100.6 to 105.6
    120
    120.7 to 126.2
    140
    140.9 to 146.9
    160
    160.9 to 167.4

    NOTICE:
    Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

  1. Check the deflection width of the speedometer indicator.

    Reference:
    Below 0.5 km/h (0.3 mph)


INSPECT TACHOMETER
  1. Connect a tune-up test tachometer, and start the engine.

  1. Compare the test results and the tachometer indications.

    DC 13.5 V at 25°C (77°F) 
    Standard Indication (rpm)
    Acceptable Range
    Data in ( ) is for Reference
    700
    630 to 770
    1,000
    (900 to 1,100)
    2,000
    (1,850 to 2,150)
    3,000
    2,800 to 3,200
    4,000
    (3,800 to 4,200)
    5,000
    4,800 to 5,200
    6,000
    (5,750 to 6,250)


INSPECT METER/GAUGE
  1. Connect the GTS to the DLC3.

  1. Perform the Active Test (Click here).

    OK:
    Each meter/gauge needle indication is normal.


INSPECT WARNING/INDICATOR LIGHT
  1. Connect the GTS to the DLC3.

  1. Perform the Active Test (Click here).

    OK:
    Each warning/indicator light can be turned on and off using the GTS.


INSPECT MULTI-INFORMATION DISPLAY (Dot Display Type)
  1. Connect the GTS to the DLC3.

  1. Perform the Active Test (Click here).

    OK:
    All dots in the multi-information display can be turned on and off using the GTS.

← DIAGNOSTIC TROUBLE CODE CHART (from Jan 2017)ON-VEHICLE INSPECTION (Jan 2015 – Dec 2016) →