ON-VEHICLE INSPECTION
Inspection · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
| CHECK INDICATOR/WARNING LIGHT |
Check the following indicators and warning lights.
Indicator/Warning Light
Switch Condition
Switch Condition
ABS warning light*9
Ignition switch off → ON
Comes on for 3 seconds
BRAKE warning light
T-BELT warning light*1
Eco driving indicator light*2
Headlight beam level control system indicator light*3, *4
DPF indicator light*5
Brake override system warning light
LED headlight warning light*3, *4
Slip indicator light*7
VSC OFF indicator light*7
Tire pressure warning light*11
TRC OFF indicator light*7
AIRBAG warning light*6
Ignition switch off → ON
Comes on for 6 seconds
MIL warning light*10
Ignition switch off → ON
- Illuminates when ignition switch turned ON
- Turns off when engine started
CHARGE warning light
OIL warning light*8
- *1: Engine Type Diesel
- *2: for Automatic Transmission
- *3: for LED Headlight
- *4: for Segment Display Type
- *5: for 1KD-FTV (w/ DPF)
- *6: w/ Airbag System
- *7: w/ VSC
- *8: except 1KD-FTV (w/ DPF)
- *9: w/ ABS
- *10: for Dot Display Type
- *11: w/ Tire Pressure Warning System
- Illuminates when ignition switch turned ON
| CHECK SPEEDOMETER |
Using a speedometer tester, check the speedometer indication according to the table below.
for mph Standard Indication
Acceptable Range
20
21.0 to 23.5
40
42.0 to 44.5
60
62.5 to 66.0
80
83.1 to 87.1
100
103.9 to 108.4
for km/h (except Australia) Standard Indication
Acceptable Range
20
21.0 to 25.0
40
41.7 to 46.2
60
62.7 to 67.2
80
83.4 to 88.4
100
104.3 to 109.3
120
125.1 to 130.6
140
145.8 to 151.8
160
166.2 to 173.2
for km/h (except 1KD-FTV, Manual Transmission [for Australia]) Standard Indication
Acceptable Range
20
20.4 to 24.4
40
41.0 to 45.5
60
61.4 to 65.9
80
82.0 to 87.0
100
10.24 to 107.4
120
122.8 to 128.3
140
143.4 to 149.4
160
163.8 to 170.3
for km/h (for 1KD-FTV, Manual Transmission [for Australia]) Standard Indication
Acceptable Range
20
20.6 to 24.6
40
41.3 to 45.8
60
61.9 to 66.4
80
82.6 to 87.6
100
103.2 to 107.7
120
123.9 to 128.9
140
144.5 to 149.5
160
165.2 to 170.2
for km/h (for Automatic Transmission [for Australia]) Standard Indication
Acceptable Range
20
20.1 to 24.1
40
40.2 to 44.7
60
60.4 to 64.9
80
80.5 to 85.5
100
100.6 to 105.6
120
120.7 to 126.2
140
140.9 to 146.9
160
160.9 to 167.4
- NOTICE:
- Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.
Check the deflection width of the speedometer indicator.
- Reference:
- Below 0.5 km/h (0.3 mph)
| CHECK TACHOMETER (w/ Tachometer) |
Connect a tune-up test tachometer, and start the engine.
Compare the test results and the tachometer indications.
DC 13.5 V at 25°C (77°F) Standard Indication (rpm)
Acceptable Range
Data in ( ) is for Reference
700
630 to 770
1,000
(900 to 1,100)
2,000
(1,850 to 2,150)
3,000
2,800 to 3,200
4,000
(3,800 to 4,200)
5,000
4,800 to 5,200
6,000
(5,750 to 6,250)
| CHECK METER/GAUGE |
Connect the GTS to the DLC3.
Perform the Active Test (Click here).
- OK:
- Each meter/gauge needle indication is normal.
| CHECK WARNING/INDICATOR LIGHT |
Connect the GTS to the DLC3.
Perform the Active Test (Click here).
- OK:
- Each warning/indicator light can be turned on and off using the GTS.
| CHECK MULTI-INFORMATION DISPLAY (Dot Display Type) |
Connect the GTS to the DLC3.
Perform the Active Test (Click here).
- OK:
- All dots in the multi-information display can be turned on and off using the GTS.
