2014-2019 Hiace · Service Manual RESTRAINTS

B1610/13 Front Airbag Sensor RH Circuit Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

DESCRIPTION

The front airbag sensor RH consists of the diagnostic circuit, the frontal deceleration sensor, etc.
If the center airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1610/13 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B1610/13
  1. The center airbag sensor assembly receives an open circuit signal in the front airbag sensor RH circuit for 2 seconds.
  2. Front airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Engine room main wire
  2. Wiring cowl to headlight harness assembly
  3. Front airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

H002750E49

INSPECTION PROCEDURE


1. CHECK DTC

  1. H045184E01
    Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1610/13 is not output.

    HINT:
    Codes other than DTC B1610/13 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

  1. C111976E01
    Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH.

  1. Using a service wire, connect B4-29 (+SR) and B4-27 (-SR) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A12-2 (+SR) -
    A12-1 (-SR)
    Always
    Below 1 Ω



NG
Go to step 8
OK


4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

  1. C111977E01
    Disconnect the service wire from connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A12-2 (+SR) -
    A12-1 (-SR)
    Always
    1 MΩ or higher



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

  1. C111977E01
    Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    A12-2 (+SR) -
    Body ground
    Always
    1 MΩ or higher
    A12-1 (-SR) -
    Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

  1. C111977E01
    Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    A12-2 (+SR) -
    Body ground
    Ignition switch ON
    Below 1 V
    A12-1 (-SR) -
    Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 11
OK


7. CHECK FRONT AIRBAG SENSOR RH

  1. H045187E03
    Connect the connectors to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1610/13 is output.
    A
    DTC B1615/14 is output.
    B
    DTC B1610/13 and B1615/14 are not output.
    C

    HINT:
    Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY

B
REPLACE FRONT AIRBAG SENSOR RH
C

USE SIMULATION METHOD TO CHECK

8. CHECK ENGINE ROOM MAIN WIRE (OPEN)

  1. C231103E01
    Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

    HINT:
    The service wire has already been inserted into connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB3-1 (+SR) -
    AB3-3 (-SR)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY

9. CHECK ENGINE ROOM MAIN WIRE (SHORT)

  1. C231105E01
    Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB3-1 (+SR) -
    AB3-3 (-SR)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY

10. CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)

  1. C231105E01
    Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    AB3-1 (+SR) -
    Body ground
    Always
    1 MΩ or higher
    AB3-3 (-SR) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY

11. CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)

  1. C231105E01
    Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the engine room main wire connector from the wiring cowl to headlight harness assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    AB3-1 (+SR) -
    Body ground
    Ignition switch ON
    Below 1 V
    AB3-3 (-SR) -
    Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK

REPAIR OR REPLACE WIRING COWL TO HEADLIGHT HARNESS ASSEMBLY


← B1000/31 Center Airbag Sensor Assembly Malfunction (from Jan 2017)B1610/13 Front Airbag Sensor RH Malfunction (Jan 2015 – Mar 2016) →