2014-2019 Hiace · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received (Bad Reception)

Circuit diagnosis · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

WIRING DIAGRAM

E277656E07
E282930E04

INSPECTION PROCEDURE

NOTICE:
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (Click here).


1. CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
  1. Check the radio automatic station search function by activating it.

    OK:
    Automatic station search function stops on a station.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are not installed.

    NOTICE:
    Do not remove optional components without permission of the customer.

    OK:
    Optional components are not installed.

    Result 
    Result
    Proceed to
    OK (for Antenna Holder Type)
    A
    OK (for Glass Antenna Type)
    B
    NG
    C



B
Go to step 3

C
Go to step 10
A

REMOVE OPTIONAL COMPONENTS (SEE NOTICE ABOVE)

3. CHECK RADIO ANTENNA

  1. E100579
    Turn the ignition switch to ACC with radio receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the antenna with holder assembly and check that noise can be heard from the speakers.

    OK:
    Noise Occurs.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


4. CHECK ANTENNA CORD SUB-ASSEMBLY

  1. E100578
    Disconnect the antenna plug from the antenna with holder assembly.

  1. Turn the ignition switch to ACC with radio receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the antenna with holder assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise Occurs.



NG
Go to step 5
OK

REPLACE ANTENNA WITH HOLDER ASSEMBLY (Click here)

5. CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)

  1. E276819
    Remove the antenna connector from the radio receiver assembly.

  1. Turn the ignition switch to ACC with radio receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise Occurs.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


6. INSPECT RADIO RECEIVER ASSEMBLY

  1. E277921E02
    Disconnect the RA radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (MAIN) - Body ground
    Ignition switch ACC, radio switch on and FM or AM selected
    11 to 14 V



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


7. CHECK ANTENNA CORD SUB-ASSEMBLY
  1. Replace the antenna cord sub-assembly with known good one and check if radio broadcasting can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 8
OK

END (ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)

8. CHECK ANTENNA WITH HOLDER ASSEMBLY
  1. Check that the antenna with holder assembly is securely installed.

    OK:
    The antenna with holder assembly is installed properly.



NG
REINSTALL ANTENNA WITH HOLDER ASSEMBLY (Click here)
OK


9. CHECK ANTENNA WITH HOLDER ASSEMBLY
  1. Replace the antenna with holder assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

10. INSPECT SIDE REAR WINDOW ASSEMBLY RH (GLASS ANTENNA)
  1. Inspect the side rear window assembly RH (glass antenna) (Click here).



NG
REPAIR OR REPLACE SIDE REAR WINDOW ASSEMBLY RH (Click here)
OK


11. CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)
E276819
  1. Remove the antenna connector from the radio receiver assembly.

  1. Turn the ignition switch to ACC with the radio receiver assembly connector connected.

  1. Turn on the radio and turn into AM mode.

  1. Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.

    OK:
    Noise occurs.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


12. INSPECT RADIO RECEIVER ASSEMBLY

  1. E277921E01
    Disconnect the RA radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (ANT+) - Body ground
    Ignition switch ACC, radio switch on and FM or AM selected
    11 to 14 V



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


13. CHECK ANTENNA CORD SUB-ASSEMBLY

  1. E288637E01
    Disconnect the radio receiver assembly connector.

  1. Remove the antenna connector from the No. 2 antenna cord sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    RA-3 (MAIN) - 2
    Always
    Below 1 Ω
    RA-5 (ANT+) - 3
    Always
    Below 1 Ω
    RA-3 (MAIN) - Body ground
    Always
    10 kΩ or higher
    RA-5 (ANT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 2 Antenna Cord Sub-assembly)



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


14. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. E288638E01
    Remove the antenna connector from the antenna cord sub-assembly.

  1. Remove the antenna connector from the No. 1 amplifier antenna assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 1
    Always
    Below 1 Ω
    3 - 3
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10 kΩ or higher
    3 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Antenna Cord Sub-assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Amplifier Antenna Assembly)



NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


15. REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the No. 1 amplifier antenna assembly with known good one and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)


← Radio Broadcast cannot be Received (Bad Reception) (Oct 2014 – Dec 2014)Radio Broadcast cannot be Received (Bad Reception) (Apr 2016 – Dec 2016) →